The wood has an allowable normal stress of allow = 15 MPa and an allowable shear...
The beam is made of timber that has an allowable bending stress of O allow = 6.5 MPa and an allowable shear stress of Tallow = 500 kPa. Part A Determine its height if it is to be rectangular and have a height-to-width ratio of 1.22. (Figure 1) Figure < Express your answer with the appropriate units. 1 of 1 ? HA h = Value Units 8 kN/m Submit Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining...
If the beam is made from wood having an allowable shear stress tallow = 3 MPa determine the maximum magnitude of P.
The wood beam has an allowable shear stress of 7 MPa. Determine the maximum shear force V that can be applied to the cross section. It is a 4 rectangles that make one rectangle with the left and right sides h=200mm b=50mm and the top and bottom are in line with the sides and inside each side and are h=50mm and b=100mm and V is in the center of it
The allowable bending stress is σ1ow-22 ksi and the allowable shear stress is Tallow 12 ksi. (Figure 1) Part A Select the lightest steel wide-flange beam from Appendix B that will safely support the loading shown. If there are several choicas of equal weight, choose the one with the shortest height. w14 × 26 W8 x 31 W10 × 39 w12 × 22 W12 × 26 W14 x 22 W10 × 30 W8 × 40 Submit Request Answer Figure 1...
The beam is constructed from three boards. (Figure 1) The allowable shear stress for the wood is Tallow = 490 psi. Each nail can resist a shear force of 485 lb. Part A Determine the maximum loads P that it can support. Express your answer to three significant figures and include appropriate units. R ? .: Å Value O O Units Submit Request Answer Figure << 1 of 1 > Part B What is the maximum allowable spacing s of...
The simply supported beam is built up from three boards by nailing them together as shown B 1 100 mm 25 mm 25 mm- 1 200 mm 25 mm The wood has an allowable shear stress of Tallow = 1.3 MPa and an allowable bending stress of allow = 8 MPa The nails are spaced at s = 75 mm, and each has a shear strength of 1.9 kN. Part A Determine the maximum allowable force P that can be...
CIVL3322 Su18 Homework Set 1 Review Problem 1.3 The allowable normal stress for member BC is allow-29 ksi and the allowable shear stress for the pins is Tallow 10 ksi (Figure 1) Part A Determine the required thickness of member BC Express your answer to three significant figures and include the appropriate units. Figure 1 of 1 t- 1 Value Units Submit Request Answer ? Part B 60 Determine the required diameter of the pin at A Express your answer...
The allowable shear stress for the material is Tallow = 6 ksi. Pin A is subjected to double shear, whereas pin B is subjected to single shear. (Figure 1) Part A Determine the required diameter of the pins at A to the nearest 1/16 in. Express your answer as an exact decimal value and include appropriate units. da= Value Units Submit Request Answer Part B Determine the required diameter of the pin at B to the nearest 1/16 in. Express...
SO mm 50 mm - 100 mm Problem 4 - Shear Stress (25 pts) The wood beam has an allowable shear stress of Tallow = 8 MPa. Determine the maximum shear force V that can be applied to the cross section. 50 mm 200 mm SO mm
The allowable tensile stress for wires AB and AC is allow = 175 MPa, and wire AB has a diameter of 5.6 mm and AC has a diameter of 6.6 mm. WA Part A Determine the greatest force P that can be applied to the chain. Express your answer to three significant figures and include appropriate units. UA ? Pmax = Value Units Submit Request Answer