In all the questions below, the material is structural steel with or= 220 MPa, E =...
In all the questions below, the material is structural steel with or= 220 MPa, E = 200 GPa, v=0.3, and a = 12x10-6/°C. Question 1 The steel shaft in Figure 1 is subjected to the torques shown. Calculate: 1. The maximum torque (Tmax) that can be applied for the shaft to operate with a safety margin of 30% (Tresca). 2. The resulting angle of twist of plane B relative to A 3. The resulting angle of twist of plane C...
the material is structural steel with σf = 220 MPa, E = 200 GPa, ν = 0.3, and α = 12x10-6/oC. please have correct answers The steel shaft AD is subjected to the torques shown in Figure 2. Calculate: 1. The internal reaction in AB 2. The internal reaction in BC 3. The internal reaction in CD 4. The maximum shaft diameter consistent with a safety margin of 50% (Tresca's criteria) 5. If points A, B, C and D are...
σf = 220 MPa, E = 200 GPa, ν = 0.3, and α = 12×10-6/°C Find the maximum torque with a 30% safety margin using Tresca Calculate the resulting angle of twist of plane B relative to A, C relative to B, and C relative to A Calculate σ1 and σ2 in AB Find the change in length of BC if ΔT = +100°C -4T +T A 0.5 m B. 0.2 m Go С X X 1 m 1 m
In all the questions below, the material is structural steel with σf = 220 MPa, E = 200 GPa, ν = 0.3, and α = 12×10-6 /℃. Question 3 The circular steel rod (D = 0.1 m) in Figure 3 is constrained by end plates and is subjected to axial load P. Calculate: 1. The internal reaction in AB 2. The internal reaction in BC 3. The maximum value for P for the rod to carry the load with a...
the material is structural steel with σf = 220 MPa, E = 200 GPa, ν = 0.3, and α = 12x10-6/oC. please help, provide clear and correct answers The cylindrical steel pressure vessel (Figure 3) has diameter D = 20 cm and thickness t=1 cm. Calculate: 1. The maximum pressure P for Tresca's criteria to yield a safety margin of 50% 2. The axial stress Ox that results from the pressure P 3. The hoop stress ge that results from...
Please provide a correct answer to these questions. The material is structural steel with of = 220 MPa, E = 200 GPa, v = 0.3, and a = 12x10-6 / 0 C The steel rod (Figure 1) is constrained between two rigid surfaces. It has a diameter D = 20 mm and is subjected to load P = 20 kN. Consider the following value below The reaction at 'A' = 13.13 KN(t) The reaction at 'B' = 6.67 KN(t) The...
MATERIAL HAS SIGMA F = 220 MPa, E = 200 GPa, Poisson's ratio v = 0.3, and alpha = 12 x 10^-6 /degrees C Question 3 The circular steel rod (D=0.1 m) in Figure 3 is constrained by end plates and is subjected to axial load P. Calculate: 1. The internal reaction in AB 2. The internal reaction in BC 3. The maximum value for P for the rod to carry the load with a safety margin of 30%. 4....
Question: "Consider the shaft in problem 10-37. Calculate the effective internal torques resulting from the applied torques. Your answer should feature a value for section AC, CD, and DB." PoF RusselLC_Hibbeler_Statics.a anics.pdf Open with ▼ 0.5 m Prob. 10-38 Prob. 10-36 10-39. The 60-mm-diameter shaft is made of 6061-T6 aluminum having an allowable shear stress of Tlow 80 MPa Determine the maximum allowable torque T. Also, find the 10-37. The splined ends and gears attached to the A992 corresponding angle...
The splined ends and gears attached to the A992 steel shaft are subjected to the torques shown. If the shaft has a diameter of 40 mm. [10 marks] a-Draw the torque diagram. [2 marks] b-Determine the angle of twist of end B with respect to end A. [3 marks] C- Determine the maximum shear stress the shaft is subjected to. [2 marks] d- If the allowable shear stress in the shaft is 300 MPa, and the allowable angle of twist...
A solid steel bar of circular cross section has diameter d = 40 mm, length L = 1.3 m and shear modulus of elasticity G = 80 GPa. The bar is subjected to torques T acting at the ends. If the torques have magnitude T = 340 Nm, what is the maximum shear stress in the bar? What is the angle of twist between the ends? If the allowable shear stress is 42 MPa and the allowable angle of twist...