A Cars What is the absolute maximum tensile stress in the stress element a to the...
A Cars What is the absolute maximum tensile stress in the stress element a to the nearest 0,01ksi? Note the member is a square cross section P=27k F-113k L-8ft b - 10 in d-1 in 90 F # 3 2 $ 4 % 5 & 7 6 8 9 W E R T Y u S F H к
Please good hand writing I will rate For a square 50x50 mm cross-section find the maximum tensile and compressive stress, if P-9.5 kN. Plot the total stress across the cross-section. 1. 100 mm 30 mm For a square 50x50 mm cross-section find the maximum tensile and compressive stress, if P-9.5 kN. Plot the total stress across the cross-section. 1. 100 mm 30 mm
a. Determine the maximum tensile and compressive bending stresses associated with the maximum positive moment.b. Determine the maximum tensile and compressive bending stresses associated with the maximum negative moment.c. Determine the absolute maximum tensile stress in the beam and the location.d. Determine the absolute maximum compressive stress in the beam and the location.e. Determine the maximum shear stress associated with maximum positive shear force.f. Determine the maximum shear stress associated with maximum negative shear force.g. Determine the absolute maximum shear...
5) Find the moment M, if the maximum tensile stress in the T shape cross section js 1 ksi. Determine the maximum compressive stress. 7) a-a is 10 in wide and 6 in deep. Determine maximum tensile and comoressive stress on a-a Find the moment M, if the maximum tensile stress in the T-shape cross section is 1ksi. Determine the maximum compressive stress. 2 in 10 in 2 in 4 in -1 in 1 inz 2 in 11 in 2...
5) Find the moment M, if the maximum tensile stress in the T shape cross section js 1 ksi. Determine the maximum compressive stress. 7) a-a is 10 in wide and 6 in deep. Determine maximum tensile and comoressive stress on a-a Find the moment M, if the maximum tensile stress in the T-shape cross section is 1ksi. Determine the maximum compressive stress. 2 in 10 in 2 in 4 in -1 in 1 inz 2 in 11 in 2...
Leaming Goal: To determine the absolute maximum bending stress in a rectangular cross section that has a circular cutout and is subjected to unsymmetrical bending in the y and z-directional planes, and to determine the angles of the neutral axes established by the applied moments. The rectangular cross section ABCD shown below has a circular cutout of diameter d= 30.0 mmthrough its center. The member is subjected to two extemally applied moments M1-6.0 kN mand M2-17.0 kN mat angles 1-35.0...
A Carvas А D Question 3 20 pts What is the maximum value can be to the nearest 0.01 k? Assume all cross sectional members are square, A-35 in? E = 25,000ksi Fy - 42 ksi 26 in 54in - Previous Next 51 F A # 3 $ 4 % 5 & 7 6 * 8 2 9 0 W E R T Y U 0 S D F G H. к
P = 20 kN. Calculate the following: 1. The maximum tensile and compressive stresses at the base of the mast A 2. The maximum tensile and compressive stresses at point B of the mast For each stress state at A and B indicate which side of the mast experiences tension and which side experiences compression. 0.25 m m D w 3 m H С. - 0.1 m mast cross section 3 m 60° Р B 584 mm 6 m mast...
use this formulas $50 kNm Determine the maximum compressive and tensile normal stress in the cross-section shown in the figure. 10 cm 15 cm 10 cm 15 cm 50 kNm Determine the maximum normal stress in the cross-sect 10 cm 15 cm 10 cm 15 cm T.C. PIRI REIS UNIVERSITY, ENGINEERING FACULTY Formulae and Constants Relations between w, V.M Torsion dV(x) = (x), NGUV) Shear stress in shaft with circular cross-section: where Axial Load for solid cross-section, for tubular cross...
Compute the maximum tensile and compressive bending stress for the cantilever beam with uniform load w = 65 kN/m and the cross-section shown below.