Question 14 Water (15°C) flows through a garden hose (ID = 14 mm) with a mean...
Kerosene at 20°C flows through a contraction section as shown. A pressure gage connected between the upstream pipe and throat section shows a pressure difference of 14 kPa. The gasoline velocity in the throat section is 12 m/s. What is the velocity (m/s) in the upstream pipe? 12m/s Kerosene at 20° C 14kPa VA = m/s Click here to access the appendices. the tolerance is +/-2%
Two garden hoses of different diameter are needed to reach a flower bed. Water flows with a speed of 1.2m/s through the bottom section of a garden hose that goes up a step 20.0 cm high. The cross-sectional area of the hose at the top of the step is half that at the bottom of the step. If the water pressure is 143 kPa at the bottom of the step, what is its pressure and velocity at the top of...
Water flows at 0.25 L/s through a 7.0- m -long garden hose 2.0 cm in diameter that is lying flat on the ground. The temperature of the water is 20 ∘ C . What is the gauge pressure of the water where it enters the hose?
Water flows at 0.20 L/s through a 12-m-long garden hose 2.5 cm in diameter that is lying flat on the ground. The temperature of the water is 20 ∘C. What is the gauge pressure of the water where it enters the hose?
Water flows at 0.25 L/s through a 12-m-long garden hose 2.0 cm in diameter that is lying flat on the ground. Part A The temperature of the water is 20 ∘C. What is the gauge pressure of the water where it enters the hose?
Apply the Darcy Weisbach equation (10.12) to the following situation. Water flows at a rate of 22 gpm and mean velocity of 180 ft/min in a pipe of length 200 feet. For a resistance coefficient of f = 0.02, find the head loss in feet. her ft Click here to access the appendices. the tolerance is +/-2%
Question 1 (1 point) Punp truck HT m Water is pumped through a 75 mm ID connector on a pump truck into a 70 m long, 75 mm ID canvas hose (friction coefficient E-0.8 mm) s shown in figure. The water then passes through a converging nozzle with a 30 mm jet exit diameter. What delivery pressure is required at the pump truck to provide a flow of 0.01 m^3/s? Your Answer: Answer units
10. Water flows through 5 meter lonq section of concrete pipe with a diameter of 10.5 cm at a velocity of 6.4 m/s. The friction factor, based on the Reynolds number and surface roughness is 0.035. The density of water is 1000 kg/mA3. What is the pressure drop along the 5 meter long section of pipe? Round your answer to the nearest tenth of a kPa-
Problem 10.032 X Incorrect. Water (70°F) flows through a nominal 4 in., schedule 40, PVC pipe at the rate of 3.0 cfs. What is the resistance coefficient f? x f= Click here to access the appendices. the tolerance is +/-9% Open Show Work Click if you would like to Show Work for this question: LINK TO TEXT By accessing this Question Assistance, you will learn while you earn points based on the Point Potential Policy set by your instructor. Question...
3. Water flows through a circular channel that has a diameter of d= 75 mm at both the inlet and outlet, as shown below. The fluid enters with uniform velocity U = 7.5 m/s. The channel makes a 90° bend that distorts the flow to produce the velocity profile at the outlet described by the function, v(r) = Vmax ( 1 -722 Assume steady, incompressible flow. Density of water is 1000 kg/m² a) Find the value of Vmax. b) Find...