Please leave comment if any issues
Refer to the following circuit. If the Zener has a specification of VzK= 5.1 V, IZK=...
(c) A loaded zener regulator is shown in Figure 3. Given Vz= 5.1 V at, Iz = 49 mA, Izk= 1 mA, Zz = 72 and Izm= 70 mA. [Satu pengatur beban zener ditunjukkan di dalam Rajah 3. Diberikan V2 = 5.1 V, Iz = 49mA, Izx = 1mA, 2-7 dan Izm = 70mA.] i) Calculate the minimum and the maximum load currents for which the zener diode will maintain the regulation. [Kirakan nilai minima dan maksima arus beban untuk...
that's all information it gives
A zener-diode voltage regulator circuit is shown below. The tage V 8.0V and the zener resistance is assumed to Problem 3: (20 points) zener diode has breakdown vol be 0 ohms. The power supply voltage Vps can vary between resistance RL can vary between 100 ohms and 1 kohm. 10V and 14V and the load Ri PS 1. Find a value of Ri such that the zener diode remains properly biased over the range of...
(a) The following circuit shows a linear
voltage regulator. Assuming the zener diode has specifications (VZ
= 2.5 V, IZ = 60 mA), select adequate resistor values to provide a
regulated output voltage Vo = 10 V from an unregulated voltage Vi =
15V.
(b) Calculate the power efficiency of the
regulator when a load RL = 10Ω is connected to the regulator
output.
(c) Briefly explain the terms “dropout”, “line
regulation”, and “load regulation”, as they apply to voltage...
Problem 3: (20 points) A zener-diode voltage regulator circuit is shown belkw zener diode has breakdown voltage Vz 8.0V and the zener resistance is nsumed to be 0 ohms. The power supply voltage Vps can vary between 10V and 14V and the lod resistance Ri can vary between 100 ohms and 1 kohm, 圧 1. Find a value of R such that the zener diode remains properly biased over the range of variation of Vps and RI (hint: the minimum...
Design a 7.5-V zener regulator circuit using a 7.5-V zener specified at 10 mA. The zener has an incremental resistance r, = 30 Q and a knee current of 0.5 mA. The regulator operates from a 10-V supply and delivers a nominal current of 5 mA to the load. What is the value of R you have chosen? What is the regulator output voltage when the supply is 10% high? Is 10% low? What is the output voltage when both...
Design a 7.5-V zener regulator circuit using a 7.5-V zener specified at 10 mA. The zener has an incremental resistance rz = 30 Ω and a knee current of 0.5 mA. The regulator operates from a 10-V supply and delivers a nominal current of 5 mA to the load. What is the value of R you have chosen? What is the regulator output voltage when the supply is 10% high? Is 10% low? What is the output voltage when both...
Question 22 The Zener diode 1N4744A, shown in the figure, has Vz=15 V, IZK = 0.25 mA and IZM-72 mA. Determine the output voltage at the load RL 15092 SRL 1502 4.0 V 8V 15V
11) 20pts. The zener limiter circuit s V R often used as a low power voltage regulator for a DC power supply. This circuit is an example in load A) Find R so that the maximum power dissipated in the zener diode is Po for any possible value of Road given P, Vin and B) What is the maximum current that the load can draw before the zener stops regulating the voltage? C) When the circuit is regulating the voltage...
4. Design a clamp circuit to clamp the negative extreme of a periodic input waveform of 10 sin(100πt)V to −5 V. Use 1 diode, 1 Zener diode, 1 resistor, and 1 capacitor of suitable values. Provide following minimum ratings of the selected components. (a) Diode - Maximum reverse voltage, peak forward current (b) Zener - Zener voltage, Zener current (c) Resistor - Resistance, power rating (d) capacitor - capacitance, Maximum voltage Assume a 0.6 V forward drop for all diodes...
Table 1: Zener Diode Parameters Description Quantity Value 1.0 W Po Absolute maximum power dissipation Typical zener voltage 5.6 V Minimum zener (knee) current 1.0 mA 45 mA Typical zener current Maximum zener current IZM Zz Zener impedance Zener knee impedance 179 mA 52 600 22 25 °C ZzK ΤΑ Rated ambient temperature 1N4004 Rs = 100 22 220 uF 1N4734A Transformer Vs = 12.6 VRMS 1N4004 60 Hz 2. Going back to Figure 1, remove the load resistance (or,...