Problem 3: (20 points) A zener-diode voltage regulator circuit is shown belkw zener diode has breakdown voltage Vz 8.0V and the zener resistance is nsumed to be 0 ohms. The power supply voltage V...
that's all information it gives A zener-diode voltage regulator circuit is shown below. The tage V 8.0V and the zener resistance is assumed to Problem 3: (20 points) zener diode has breakdown vol be 0 ohms. The power supply voltage Vps can vary between resistance RL can vary between 100 ohms and 1 kohm. 10V and 14V and the load Ri PS 1. Find a value of Ri such that the zener diode remains properly biased over the range of...
The circuit above is a Zener voltage regulator using D1N750 zener diode with Vz=4.7V: 1. Calculate the minimum value of E in order to have the voltage across RL regulated VL=Vz 2. Using Orcad PSpice schematics, simulate the circuit using bias point and find Iz, IL, Is and Vz (the circuit must have all voltages and currents values shown). 3. Using Orcad PSpice schematics, use DC sweep to vary RL from 200 ohm to 1000 ohm and plot VL (for...
In the voltage regulating circuit that is shown the zener diode has Vz=4.8V. Its current its limited by the interval . Find the interval of the possible load resistances and the minimum and maximum power dissipated by the diode. Answer and 5mA < 12 < 100m.4
2.19 Consider the circuit shown in Figure P2.19. The Zener diode voltage is Vz = 3.9 V and the Zener diode incremental resistance is ra = 0. (a) Deter- mine Iz, Il, and the power dissipated in the diode. (b) Repeat part (a) if the 4 k 32 load resistor is increased to 10 KS2. 12 k22 " 1112 vz$ 111 462 20 v= Figure P2.19
6. In the zener diode regulator circuit below calculate the value of the current through the zener Diode if the power supply is rated at 24 volts @ 500 milliamperes. The load voltage is 12 volts and draws a current of 300 milliamperes. Also calculate the value of the series resistance R. ZENDER LOAD DIODE 24 VDC Vz 12 Volts @ 300 mA
(a) The following circuit shows a linear voltage regulator. Assuming the zener diode has specifications (VZ = 2.5 V, IZ = 60 mA), select adequate resistor values to provide a regulated output voltage Vo = 10 V from an unregulated voltage Vi = 15V. (b) Calculate the power efficiency of the regulator when a load RL = 10Ω is connected to the regulator output. (c) Briefly explain the terms “dropout”, “line regulation”, and “load regulation”, as they apply to voltage...
11) 20pts. The zener limiter circuit s V R often used as a low power voltage regulator for a DC power supply. This circuit is an example in load A) Find R so that the maximum power dissipated in the zener diode is Po for any possible value of Road given P, Vin and B) What is the maximum current that the load can draw before the zener stops regulating the voltage? C) When the circuit is regulating the voltage...
In α Zoner diode voltage regulator circuit, the source series resistance & 20 Ω Zoner voltage V.- volt and load rosistance R.-200 Ω lf souree voltage Vs can vary from 20 voll to 30 volt, find the maximum and minimum eurrent in the diode? ) 18 R i
Ctri Question 3 (20 Marks) Lab 1-Zener Circuits and Applications Theory: Zener diode is designed to operate in reverse conduction. Zener breakdown occurs at a precisely defined voltage, allowing the diode to be used as a voltage reference or clipper. While Zener diodes are usually operated in reverse conduction, they may also be operated in cutoff and forward conduction. There are two different effects that are used in "Zener diodes". The only practical difference is that the two types have...
5000 10.2 S pts) The Zener diode in the circuit on the right voltage V 20 = 8.5V., and Zener resistancerz the circuit on the right has a Zener d) Find the Thevenin equivalent circuit as seen by lo b) Find the output voltage if a loa Find the output voltage if a load R, is connected and it draws a 1.5 mA current. Determine the value of RL c) How small can the load R, be, while ensuring that...