In the voltage regulating circuit that is shown the zener diode has Vz=4.8V. Its current its limited by the interval .
Find the interval of the possible load resistances and the minimum and maximum power dissipated by the diode.
Answer and
In the voltage regulating circuit that is shown the zener diode has Vz=4.8V. Its current its...
2.19 Consider the circuit shown in Figure P2.19. The Zener diode voltage is Vz = 3.9 V and the Zener diode incremental resistance is ra = 0. (a) Deter- mine Iz, Il, and the power dissipated in the diode. (b) Repeat part (a) if the 4 k 32 load resistor is increased to 10 KS2. 12 k22 " 1112 vz$ 111 462 20 v= Figure P2.19
Problem 3: (20 points) A zener-diode voltage regulator circuit is shown belkw zener diode has breakdown voltage Vz 8.0V and the zener resistance is nsumed to be 0 ohms. The power supply voltage Vps can vary between 10V and 14V and the lod resistance Ri can vary between 100 ohms and 1 kohm, 圧 1. Find a value of R such that the zener diode remains properly biased over the range of variation of Vps and RI (hint: the minimum...
.65 Consider the circuit of Fig. P3.21 with a zener diode connected in place of the pn junction diode. If VzK = 5 V, plot the voltage uz versus the voltage VB over the range-12V < VO < 12V.
that's all information it gives A zener-diode voltage regulator circuit is shown below. The tage V 8.0V and the zener resistance is assumed to Problem 3: (20 points) zener diode has breakdown vol be 0 ohms. The power supply voltage Vps can vary between resistance RL can vary between 100 ohms and 1 kohm. 10V and 14V and the load Ri PS 1. Find a value of Ri such that the zener diode remains properly biased over the range of...
6. In the zener diode regulator circuit below calculate the value of the current through the zener Diode if the power supply is rated at 24 volts @ 500 milliamperes. The load voltage is 12 volts and draws a current of 300 milliamperes. Also calculate the value of the series resistance R. ZENDER LOAD DIODE 24 VDC Vz 12 Volts @ 300 mA
11) 20pts. The zener limiter circuit s V R often used as a low power voltage regulator for a DC power supply. This circuit is an example in load A) Find R so that the maximum power dissipated in the zener diode is Po for any possible value of Road given P, Vin and B) What is the maximum current that the load can draw before the zener stops regulating the voltage? C) When the circuit is regulating the voltage...
The circuit above is a Zener voltage regulator using D1N750 zener diode with Vz=4.7V: 1. Calculate the minimum value of E in order to have the voltage across RL regulated VL=Vz 2. Using Orcad PSpice schematics, simulate the circuit using bias point and find Iz, IL, Is and Vz (the circuit must have all voltages and currents values shown). 3. Using Orcad PSpice schematics, use DC sweep to vary RL from 200 ohm to 1000 ohm and plot VL (for...
(a) The following circuit shows a linear voltage regulator. Assuming the zener diode has specifications (VZ = 2.5 V, IZ = 60 mA), select adequate resistor values to provide a regulated output voltage Vo = 10 V from an unregulated voltage Vi = 15V. (b) Calculate the power efficiency of the regulator when a load RL = 10Ω is connected to the regulator output. (c) Briefly explain the terms “dropout”, “line regulation”, and “load regulation”, as they apply to voltage...
Question 22 The Zener diode 1N4744A, shown in the figure, has Vz=15 V, IZK = 0.25 mA and IZM-72 mA. Determine the output voltage at the load RL 15092 SRL 1502 4.0 V 8V 15V
50012 V R 2. (15 points) The Zener diode in the circuit has a voltage Vzo = 8V. When the diode current is 10mA, the voltage across it is V = 8.25 V. The supply voltage is: Vpc = 15 V a) Find the small resistance rz of the diode. b) Replace the diode by its model, and find the Thevenin equivalent circuit to the left of the load RL c) Find the voltage V, across the load for two...