A steel I-beam with a span of 20 feet will support both a concentrated load of...
14.54 A simply supported rectangular beam with a span of 6 ft has a concentrated load of 4.1 kip at midspan. Se- lect the lightest rectangular wood beam that can safely support the loads (neglect the weight of the beam). The allowable stress in bending is 1200 psi and in shear parallel to the grain 100 psi 14.54 A simply supported rectangular beam with a span of 6 ft has a concentrated load of 4.1 kip at midspan. Se- lect...
A rectangular reinforced concrete beam of span 16 ft supports a concentrated load of 40 kips at mid-point of the beam and a uniformly-distributed load of 4 kips/ft over the entire span. Given: (a) The breadth of the beam is 18 inches. (b) Concrete compressive strength, fc, is 3500 psi. (c) Rebar is Grade 40 steel i) Determine the maximum moment and maximum shear acting on the beam. ii) Determine the minimum effective depth 'd' of the beam section (rounded...
A rectangular reinforced concrete beam of span 16 ft supports a concentrated load of 40 kips at mid-point of the beam and a uniformly-distributed load of 4 kips/ft over the entire span. Given: (a) The breadth of the beam is 18 inches. (b) Concrete compressive strength, f 'c, is 3500 psi. (c) Rebar is Grade 40 steel i) Determine the maximum moment and maximum shear acting on the beam. ii) Determine the minimum effective depth 'd' of the beam section...
16.6a) A simply supported beam is to span 15 ft. It will support a uniformly distributed load of 2 kips/ft over the full span and a concentrated load of 60 kips at mid-span. What is the required plastic section modulus Zx? (Include self-weight) 16.6b) A simply supported beam is to span 15 ft. It will support a uniformly distributed load of 2 kips/ft over the full span and a concentrated load of 60 kips at mid-span. Deflection is not to...
Select the lightest W shape to support a uniformly distributed load of 80 kN/m and concentrated loads of 26kN located 4.5 m from the end of the beam. The beam is 16 m, Deflection is not to exceed span/280.
2. (1.5 points) A 24-ft simple span that supports three (3) service concentrated live load of 20 kips each at quarter points is laterally unbraced except at its ends and the center line. If the maximum permissible center line deflection under service live load equal L/400, select the lightest Wsection of 50 ksi steel, considering moment, shear, and deflection. Neglect beanm weight. Use Cb-1.0. 2. (1.5 points) A 24-ft simple span that supports three (3) service concentrated live load of...
A steel beam is simply supported over a span of 20 feet and carries a total design point load of 6 kips at the center of the span. The moment of inertia (1) for the beam is 245 in4. Neglecting the beam weight, the maximum load deflection of the beam is with a point load in.(Fill in the blank and show calculation below) Show equation(s) used and calculation(s): A steel beam is simply supported over a span of 20 feet...
Problem 2: the most economical (lightest) W shape to support a uniformly distributed load of 4k/ft (This load includes the weight of the beam) on a simply supported span of 25 ft as shown. Assume the yield stress of the steel to be 50 ksi. The deflection limit (Allowable) is Select 360 w 4 kips/ft 25'-0" R 50 kips RB 50 kips
A rectangular beam that must carry a service live load of 2.47 kips/ft and a calculated dead load of 1.05 kips/ft on an 18 ft simple span is limited in cross section for architectural reasons to 10 in. width and 20 in. total depth. If fy=60,000 psi and fc′=4,000 psi, what steel area(s) must be provided. A rectangular beam that must carry a service live load of 2.47 kips/ft and a calculated dead load of 1.05 kips/ft on an 18...
Consider the beam subjected to a concentrated load consisting of 2.25 kips of dead load and 5.55 kips of live load at point B. Find maximum factored beam shear, moment, and deflection. Consider the beam and loading given below. The beam is subjected to a concentrated load consisting of 2.25 kips of dead load and 5.55 kips of live load at point B. Neglect beam weight. You may use any information from the AISC Manual, a) Draw the general shape...