Points A and B are 6 km apart along a new 70 cm. cast iron pipe carrying water. A is 10m higher than B. If the pressure at B is 145 kPa greater than A. (f = 0.019). Determine the headloss from A to B and the amount of flow.
Please upvote if you like the answer, Thank you.!
Prob-1 Points A and B are 1 km apart along a 20 cm new steel pipe. Point B is 20 m higher than A. With a flow from A to B of 0.03 m/s of crude oil (S 0.82) at 10°C (u = 10 Ns/m), What pressure must be maintained at A if the pressure at B is to be 400 kPa?
Points A and B are 1 km apart along a 15 cm new steel pipe. Point B is 20 m higher than A. With a flow from A to B of 0.03 m/s of crude oil (S 0.82) at 10°C (u = 10 ²N s/m), What pressure must be maintained at A if the pressure at B is to be 300 kPa? Situation: Crude oil flows through a steel pipe. Properties: D=15cm, Q = 0.03 m/s. S = 0.82.4 =...
3. Paints A and B are 900 m apart along a new 150 mm pipe. Bis 30 m higher than B. With 30 liters/sec of water flowing from A to B, com- pute the necessary pressure at A if the pressure at B is to be 275 KPa f 0.024 0m
please show clear steps solution. Prob-1 Points A and B are 1 km apart along a 20 cm new steel pipe. Point Bis 20 m higher than A. With a flow from A to B of 0.03 m/s of crude oil (S 0.82) at 10°C (1 = 102N s/m'), What pressure must be maintained at A if the pressure at B is to be 400 kPa? Table 104 EQUIVALENT SAND-GRAIN ROUGHNESS, FOR VARIOUS PIPE MATERIALS Boundary Material M A. Inches...
Hydraulics Problem 4 (25 points) Water flows through a cast iron pipe at 1.2 2.5[km) long with an elevation drop of 50[m]. . The pipe has a diameter 0.6[m] and is 1. Ignoring minor losses, calculate the pressure head drop per unit length over the course of the pipe. Write the equation(s) needed to compute the pressure drop per unit length. First, express - only as a function of all the given parameters (you may use several equations if needed,...
5) A 6-km cast-iron (new) pipeline conveys 0.32 m/s of water at 30°C. If the pipe diameter is 30 cm, compare the head loss calculated (a) Darcy-Weibach equation (f = 0.0195), (b) the Hazen- William equation (Chw = 130), and (c) the Manning equation (n=0.011). Use Excel. (Max. 15 Points) 6) Pipes AB and CF in figure below have a diameter of 48 in possess a Hazen-Williams coefficient factor of 100 and carry a discharge of 120 ft/s. The length...
Two water reservoirs A and B are connected to each other through a 35m-long, 2-cm-diameter cast iron pipe with a sharp-edged entrance. The pipe also involves a swing check valve and a fully open gate valve. The water level in both reservoirs is the same, but reservoir A is pressurized by compressed air while reservoir B is open to the atmosphere at 94 kPa. If the initial flow rate through the pipe is 1.2 L/s, determine the air pressure (gage)...
Please solve a,b,c,d,e,f 1) A water fountain is to be installed at a remote location by attaching a cast iron pipe directly to a water main through which water is flowing. The entrance to the pipe is sharp-edged 15m (K-0.5), and the 15m long piping system involves three 90 bends without vanes (K1.1), a fully open gate valve (K.-0.2), and a fully open angle valve (K-5). If the diameter of the pipe is 2 em and the system is to...
The total length of the piping system made of cast iron providing hot water to a house is considered to have a 42m length with a constant diameter. The entrance gage pressure is 85 kPa and exit at 15 kPa gaged. Consider the water density equal 980 Kg/m' and the viscosity 1.138x10 Kg/ms. a) Compute the piping system diameter if the volumetric flow rate provided by this system is equal to 0.1 L/s. There is no pump present in this...
Two water reservoirs A and B are connected to each other through a 35m-long, 2-cm-diameter cast iron pipe with a sharp-edged entrance. The pipe also involves a swing check valve and a fully open gate valve. The water level in both reservoirs is the same, but reservoir A is pressurized by compressed air while reservoir B is open to the atmosphere at 94 kPa. If the initial flow rate through the pipe is 1.2 L/s, determine the air pressure (gage)...