A couple is applied to the ends of the rotating steel shaft as shown below with a force F= 350 lb, in the form of a repeated loading. The shaft is commercially grounded. The following properties are specified for the material Sut = 110ksi and Sy = 80ksi. The reliability specified is 95%. Find the factor of safety for the 8in shaft using the Modified Goodman Design Theory for infinite life. Ignore the stress concentration at the fillet.
All answers are boxed and underlined. Thank You and stay safe.
If this is helpful, please UPVOTE. Thank you !!
A couple is applied to the ends of the rotating steel shaft as shown below with...
A couple is applied to the ends of the steel shaft as shown below with a force F= 150 lb, the shaft is commercially grounded. The following properties are specified for the material Sut = 90ksi and Sy = 65ksi. The reliability specified is 95%. Find the factor of safety for the Sin shaft using the Modified Goodman Design Theory.
A rotating circular shaft, machined from AISI 1095 Q&T steel, is subjected to a torque that varies from a value of 200 N.m to 400 N.m and to a fluctuating bending moment that varies from a value of -100 N.m to 300 N.m. Also an axial tensile force of 5 kN acts on the element. The torque and the bending moments have their peak values at the same time and their frequencies are same. Find the factor of safety of...
A rotating shaft is made of 42 mm by 4 mm thick cold-drawn round steel tubing and has a 6 mm diameter hole drilled transversely through it. The shaft is subjected to a pulsating torque fluc- tuating from 20 to 160 Nm and a completely reversed bending moment of 200 Nm. The steel tubing has a minimum strength of Sut 410 MPa (60 ksi). The static stress-concentration factor for the hole is 2.4 for bending and 1.9 for torsion. The...
The shaft shown is made of AISI 1040 CD steel. It is machine finished and is subjected to a repeated bending stress of 15ksi. The diameter at the shoulder is 1.3in and will be used at a temperature of 400F. Estimate: (a) The endurance limit at 95% reliability (b) Endurance strength at 105 cycles and show on S-N plot 10 (c) Plot the design region by Modified Goodman theory and determine if failure is by yield or fatigue (d) Find the factor of safety...
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a disc (not shown) which meshes with the disc at D as shown. The force F from the drive disc acts vertically as shown in figure where F = 2.2 kN. The shaft transmits a torque to point A of TA=380 Nm. The shaft is machined from steel. a. Using a factor of safety of 3, determine the shaft diameter at various...
A rotating shaft is made of AISI 1035 CD steel is subjected to an axial load of 710N, a fluctuating torque load from 60 to 120 N.m, and a completely reversed bending moment of 160N.m. The shaft has a diameter of 30mm, and operates at T=250°C, and has a life reliability of 95%. Note that the fatigue stress-concentration factor for bending Kfb is 1.49 and that for torque Kft is 2.65..1. Draw the Yield (Langer) line 2. Modified Goodman line. 3. Calculate...
The cantilever bar in the figure is made from AISI 1018 CD steel and is statically loaded with Fy = 800 N, and Fx = Fz = 0. The fillet radius at the wall is 2 mm with theoretical stress concentrations of 1.5 for bending, 1.2 for axial, and 2.1 for torsion.Sut = 440 MPa = 64 kpsi, Sy = 370 MPa = 54 kpsi. Analyze the stress situation in rod AB by obtaining the following information.a) Determine the precise...
In the figure below, a rotating shaft (for speed reducing gearbox) is subjected to radial forces at A= 400 lbr .and at C = 800 Ibr. These radial forces are caused by spur gears mounted to shaft (a result of the pressure angle of the teeth, 20 degrees) that mesh with 2 other spur gears, not shown. Also, The shaft transmits a constant torque of 11110 in-lbr (925 ft-lbr) due to the tangential force (Wt: transmitted load) at C of...
Problem 1 (a) (200 points) Shaft fatigue strength In the figure below, a rotating shaft (for speed reducing gearbox) is subjected to radial forces at A-400 lbrand at C-800 iht. These radial forces are caused by spur gears mounted to shar (a result of the pressure angle of the teeth, 20 degrees) that mesh with 2 other spur gears, not shown. Also, The shaft transmits a constant torque of 11110 in-Ibr (925 - due to the tangential force (s: transmitted...
A simply supported shaft is shown in Figure. A constant-magnitude transverse load P is applied as the shaft rotates subject to a time-varying torque that varies from Tmin to Tmax. For ihe data in the row(s) assigned from Table, find the diameter of shaft required to obtain a safety factor of 2 in fatigue loading if the shaft is steel of Sut = 108 kpsi and Sy = 62 kpsi. The dimensions are in inches, the force in pounds, and...