Homework Answers
Add Answer to:
Water at 15° is flowing at the rate of 14.4m²/hr (Fig. 2). The head added by...
Water at 15° is flowing at the rate of 14.4m/hr (Fig. 2). The head added by...
Water at 15° is flowing at the rate of 14.4m/hr (Fig. 2). The head added by the pump is equivalent to 80 m. Both tanks are vented. Suction line is 15m long and discharge line is 200m long. Both suction and discharge lines are standard 2-inch (5.1cm) clean steel pipe with roughness value of s=5.1 x 10ʻm. Assume that the entrance from Tankl is through a rounded inlet with inlet radius of 10mm and that the elbows are standard 90°....
- + Fit to page LO (15 marks) Exercise 2 Water at 15° is flowing at...
- + Fit to page LO (15 marks) Exercise 2 Water at 15° is flowing at the rate of 14.4m/hr (Fig. 2). The head added by the pump is equivalent to 80 m. Both tanks are vented. Suction line is 15m long and discharge line is 200m long. Both suction and discharge lines are standard 2-inch (5.1cm) clean steel pipe with roughness value of s=5.1 x 10ʻm. Assume that the entrance from Tankl is through a rounded inlet with inlet...
Q) Methyl alcohol at 25 C is flowing at the rate of 54000 lit/h. The suction line is a standard 4...
yes
you can
Q) Methyl alcohol at 25 C is flowing at the rate of 54000 lit/h. The suction line is a standard 4-in Schedule 40 steel pipe, 1500 cm long. The total length of 2-in Schedule 40 steel pipe in the discharge line is 200 m. Assume the entrance from reservoir 1 is through a square-edged inlet and that the elbows are 90° standard. The valve is fully open globe valve. A) List the piping systems components B) Generate...
what is the velocity head at the inlet pump? Find the value of head loss (consider...
what is the velocity head at the inlet pump?
Find the value of head loss (consider entrance, friction,
elbow and valve losses). Also, find pressure at the inlet
pump
water is at 80 degrees C
Water is being pumped from the tank at a rate of 475 L/min
-115 m E Pump Globe valve fully open DN 65 Schedule 40 steel pipe 1.40 m 0.75 m Standard elbows (2)
1 A pump delivers water from the lower reservoir to the upper reservoir at a rate of 60 L/s. Both...
1 A pump delivers water from the lower reservoir to the upper reservoir at a rate of 60 L/s. Both the suction and discharge pipes are DN 150 schedule 40steel pipe. The length of the suction pipe leading to the pump is 3.5 m, and 7 m of discharge pipe extend from the pump outlet to the upper tank. There are three standard 900 elbows and a fully open gate valve. The depth of the fluid level inside the lower...
Water at 160° Fis drawn at the rate of 400 gal/min from a vented tank into...
Water at 160° Fis drawn at the rate of 400 gal/min from a vented tank into the 2-in Sch 40 suction line of the pump made of steel. The suction line has a total length of 10 ft. the discharge line elevates the water 30 ft to the level of the large heat exchanger. The discharge line has a total length of 40 ft. The system contains: 2 standard elbows, 1 swing check valve, and 4 open gate valves. Assuming...
The system below shows a simplified schematic of an oil transfer system between tanks, from left...
The system below shows a simplified schematic of an oil transfer system between tanks, from left to right: L L The oil specific gravity is 0.77 and its viscosity is 2.7 [cP). The pipes are horizontal and coaxial (neglect difference in height between suction and discharge). The tanks are closed but vented so that they are at atmospheric pressure ([atm]). Assume for simplicity that the liquid level in each tank is 2.5 (m) above the level of the pipes (in...
You need to pump water at 20 C from an open reservoir at flow rate of...
You need to pump water at 20 C from an open reservoir at flow rate of 1.4 x 10^-3 m3/s through a pipe with an inside diameter of 0.03m, using a centrifugal pump having an (NPSH)aq =2.5 m and the equivalent length on the suction side is 3m. There are several minor losses: four standar 90 flanged elbows, and fully open flanged globe valve, fully open flanged gate valve, and the Entrance. What is the the maximum distance above the...
Fluid Mechanics & Fluid Power Determine the NPSH available. The pressure in the tank is - 20 kPa at 70 °C (atmospheric pressure is 100.5 kPa). The water level in the tank is 2.5 above the pump in...
Fluid Mechanics & Fluid Power
Determine the NPSH available. The pressure in the tank is - 20 kPa at 70 °C (atmospheric pressure is 100.5 kPa). The water level in the tank is 2.5 above the pump inlet. The pipe is 1%", schedule 40 with a total length of 12 m. The elbow is standard, and the globe valve is fully open. The flow rate is 95 L/min. FIGURE 13.27 llustration of pump performance for different impeller diameters with net...
Water, with density of 1000 kg/m3 and kinematic viscosity of 1.0 x 10- m2/s, is pumped through a ...
Water, with density of 1000 kg/m3 and kinematic viscosity of 1.0 x 10- m2/s, is pumped through a total length of 60 m of pipe from a lower reservoir to a higher reservoir. The inner diameter of the pipe is 30 cm. Both reservoirs are open to the atmosphere, and the water surface of the higher reservoir is 10 m above that of the lower reservoir. The entrance from the lower reservoir to the pipe is sharp-edged, and along the...
Water at 15° is flowing at the rate of 14.4m/hr (Fig. 2). The head added by the pump is equivalent to 80 m. Both tanks are vented. Suction line is 15m long and discharge line is 200m long. Both suction and discharge lines are standard 2-inch (5.1cm) clean steel pipe with roughness value of s=5.1 x 10ʻm. Assume that the entrance from Tankl is through a rounded inlet with inlet radius of 10mm and that the elbows are standard 90°....
- + Fit to page LO (15 marks) Exercise 2 Water at 15° is flowing at the rate of 14.4m/hr (Fig. 2). The head added by the pump is equivalent to 80 m. Both tanks are vented. Suction line is 15m long and discharge line is 200m long. Both suction and discharge lines are standard 2-inch (5.1cm) clean steel pipe with roughness value of s=5.1 x 10ʻm. Assume that the entrance from Tankl is through a rounded inlet with inlet...
yes
you can
Q) Methyl alcohol at 25 C is flowing at the rate of 54000 lit/h. The suction line is a standard 4-in Schedule 40 steel pipe, 1500 cm long. The total length of 2-in Schedule 40 steel pipe in the discharge line is 200 m. Assume the entrance from reservoir 1 is through a square-edged inlet and that the elbows are 90° standard. The valve is fully open globe valve. A) List the piping systems components B) Generate...
what is the velocity head at the inlet pump?
Find the value of head loss (consider entrance, friction,
elbow and valve losses). Also, find pressure at the inlet
pump
water is at 80 degrees C
Water is being pumped from the tank at a rate of 475 L/min
-115 m E Pump Globe valve fully open DN 65 Schedule 40 steel pipe 1.40 m 0.75 m Standard elbows (2)
1 A pump delivers water from the lower reservoir to the upper reservoir at a rate of 60 L/s. Both the suction and discharge pipes are DN 150 schedule 40steel pipe. The length of the suction pipe leading to the pump is 3.5 m, and 7 m of discharge pipe extend from the pump outlet to the upper tank. There are three standard 900 elbows and a fully open gate valve. The depth of the fluid level inside the lower...
Water at 160° Fis drawn at the rate of 400 gal/min from a vented tank into the 2-in Sch 40 suction line of the pump made of steel. The suction line has a total length of 10 ft. the discharge line elevates the water 30 ft to the level of the large heat exchanger. The discharge line has a total length of 40 ft. The system contains: 2 standard elbows, 1 swing check valve, and 4 open gate valves. Assuming...
The system below shows a simplified schematic of an oil transfer system between tanks, from left to right: L L The oil specific gravity is 0.77 and its viscosity is 2.7 [cP). The pipes are horizontal and coaxial (neglect difference in height between suction and discharge). The tanks are closed but vented so that they are at atmospheric pressure ([atm]). Assume for simplicity that the liquid level in each tank is 2.5 (m) above the level of the pipes (in...
Fluid Mechanics & Fluid Power
Determine the NPSH available. The pressure in the tank is - 20 kPa at 70 °C (atmospheric pressure is 100.5 kPa). The water level in the tank is 2.5 above the pump inlet. The pipe is 1%", schedule 40 with a total length of 12 m. The elbow is standard, and the globe valve is fully open. The flow rate is 95 L/min. FIGURE 13.27 llustration of pump performance for different impeller diameters with net...
Water, with density of 1000 kg/m3 and kinematic viscosity of 1.0 x 10- m2/s, is pumped through a total length of 60 m of pipe from a lower reservoir to a higher reservoir. The inner diameter of the pipe is 30 cm. Both reservoirs are open to the atmosphere, and the water surface of the higher reservoir is 10 m above that of the lower reservoir. The entrance from the lower reservoir to the pipe is sharp-edged, and along the...
Most questions answered within 3 hours.
-
At the start of a CD it is spinning at a rate of 525 rpm
(revolutions...
asked 28 minutes ago -
4. Without doing any calculations, predict whether the observed
∆T would increase, decrease or remain the...
asked 1 hour ago -
Based on the range, which of the following sets of scores has
the greatest variability? 3,...
asked 2 hours ago -
Ripples in a pond travel at a velocity of 3 m/s with one peak
passing a...
asked 2 hours ago -
A man stands on the roof of a building of height 13.0 mm and
throws a...
asked 2 hours ago -
The extent to which assets are financed by borrowed funds and
other liabilities is indicated by:...
asked 3 hours ago -
Explain in detail
Germany is the fifth largest economy
explain what goods and services Germany specializes...
asked 4 hours ago -
The density of platinum is 21.45 g/mL. If a cube of platinum
with a mass of...
asked 4 hours ago -
Accounts Receivable
Sales
A/R Posting
Extended Sales Invoice
Packing Slip
Compare invoice to packing slip 2...
asked 4 hours ago -
Michaella, age 23, is a full-time law student and is claimed by
her parents as a...
asked 4 hours ago -
Why are polymers not typically casted into products?
asked 4 hours ago -
When rolling a die 129 times, what is the probability of rolling
a 6 no more...
asked 4 hours ago