Homework Answers
Add Answer to:
- + Fit to page LO (15 marks) Exercise 2 Water at 15° is flowing at...
Water at 15° is flowing at the rate of 14.4m/hr (Fig. 2). The head added by...
Water at 15° is flowing at the rate of 14.4m/hr (Fig. 2). The head added by the pump is equivalent to 80 m. Both tanks are vented. Suction line is 15m long and discharge line is 200m long. Both suction and discharge lines are standard 2-inch (5.1cm) clean steel pipe with roughness value of s=5.1 x 10ʻm. Assume that the entrance from Tankl is through a rounded inlet with inlet radius of 10mm and that the elbows are standard 90°....
Water at 15° is flowing at the rate of 14.4m²/hr (Fig. 2). The head added by...
Water at 15° is flowing at the rate of 14.4m²/hr (Fig. 2). The head added by the pump is equivalent to 80 m. Both tanks are vented. Suction line is 15m long and discharge line is 200m long. Both suction and discharge lines are standard 2-inch (5.1cm) clean steel pipe with roughness value of ε = 5.1 x 108m. Assume that the entrance from Tankl is through a rounded inlet with inlet radius of 10mm and that the elbows are...
Q) Methyl alcohol at 25 C is flowing at the rate of 54000 lit/h. The suction line is a standard 4...
yes
you can
Q) Methyl alcohol at 25 C is flowing at the rate of 54000 lit/h. The suction line is a standard 4-in Schedule 40 steel pipe, 1500 cm long. The total length of 2-in Schedule 40 steel pipe in the discharge line is 200 m. Assume the entrance from reservoir 1 is through a square-edged inlet and that the elbows are 90° standard. The valve is fully open globe valve. A) List the piping systems components B) Generate...
1.por - + 2 Fit to page ID Page Exercise 1 (15 marks) Water at 20°...
1.por - + 2 Fit to page ID Page Exercise 1 (15 marks) Water at 20° flows in pipeline system shown below (Fig.1) at rate of 32400 l/hr. Pipe 1 is 15m long and 0.044 m outer diameter and pipe 2 is 100m long and 0.034m outer diameter. The thickness of both pipes is 2mm. Pipe 1 is a ductile iron uncoated pipe and pipe 2 is ductile iron coated pipe. There are totally 4 elbows in the system (two...
Water at 160° Fis drawn at the rate of 400 gal/min from a vented tank into...
Water at 160° Fis drawn at the rate of 400 gal/min from a vented tank into the 2-in Sch 40 suction line of the pump made of steel. The suction line has a total length of 10 ft. the discharge line elevates the water 30 ft to the level of the large heat exchanger. The discharge line has a total length of 40 ft. The system contains: 2 standard elbows, 1 swing check valve, and 4 open gate valves. Assuming...
1 A pump delivers water from the lower reservoir to the upper reservoir at a rate of 60 L/s. Both...
1 A pump delivers water from the lower reservoir to the upper reservoir at a rate of 60 L/s. Both the suction and discharge pipes are DN 150 schedule 40steel pipe. The length of the suction pipe leading to the pump is 3.5 m, and 7 m of discharge pipe extend from the pump outlet to the upper tank. There are three standard 900 elbows and a fully open gate valve. The depth of the fluid level inside the lower...
The system below shows a simplified schematic of an oil transfer system between tanks, from left...
The system below shows a simplified schematic of an oil transfer system between tanks, from left to right: L L The oil specific gravity is 0.77 and its viscosity is 2.7 [cP). The pipes are horizontal and coaxial (neglect difference in height between suction and discharge). The tanks are closed but vented so that they are at atmospheric pressure ([atm]). Assume for simplicity that the liquid level in each tank is 2.5 (m) above the level of the pipes (in...
Please solve a,b,c,d,e,f 1) A water fountain is to be installed at a remote location by attaching a cast iron pipe directly to a water main through which water is flowing. The entrance to the pipe...
Please solve a,b,c,d,e,f
1) A water fountain is to be installed at a remote location by attaching a cast iron pipe directly to a water main through which water is flowing. The entrance to the pipe is sharp-edged 15m (K-0.5), and the 15m long piping system involves three 90 bends without vanes (K1.1), a fully open gate valve (K.-0.2), and a fully open angle valve (K-5). If the diameter of the pipe is 2 em and the system is to...
Question 1 50 marks Part A (30 marks) In a proposed water supply system, two large...
Question 1 50 marks Part A (30 marks) In a proposed water supply system, two large reservoirs will be connected with a pipeline 9 km long and with an elevation difference of 72 metres between the full water levels of the reservoirs. The pipe will be required to convey a minimum discharge of 450 L/s. The proposed pipe material is UPVC. Fittings in the pipeline include one 90° short radius elbow and one gate valve fully open. Pipeline entrance and...
A pump transports water from Tank 1 to Tank 2 through a constant-diameter piping system as...
A pump transports water from Tank 1 to Tank 2 through a constant-diameter piping system as shown below (not to scale). The flow rate is controlled by two gate valves, the gate valve I controls the main pipeline, while the gate valve II controls the loop line from T-joint A to T-joint B. All pipes are galvanized steel pipe of diameter D = 4 in. It has a total length of Li2= 620 ft from tank 1 to tank 2....
Water at 15° is flowing at the rate of 14.4m/hr (Fig. 2). The head added by the pump is equivalent to 80 m. Both tanks are vented. Suction line is 15m long and discharge line is 200m long. Both suction and discharge lines are standard 2-inch (5.1cm) clean steel pipe with roughness value of s=5.1 x 10ʻm. Assume that the entrance from Tankl is through a rounded inlet with inlet radius of 10mm and that the elbows are standard 90°....
Water at 15° is flowing at the rate of 14.4m²/hr (Fig. 2). The head added by the pump is equivalent to 80 m. Both tanks are vented. Suction line is 15m long and discharge line is 200m long. Both suction and discharge lines are standard 2-inch (5.1cm) clean steel pipe with roughness value of ε = 5.1 x 108m. Assume that the entrance from Tankl is through a rounded inlet with inlet radius of 10mm and that the elbows are...
yes
you can
Q) Methyl alcohol at 25 C is flowing at the rate of 54000 lit/h. The suction line is a standard 4-in Schedule 40 steel pipe, 1500 cm long. The total length of 2-in Schedule 40 steel pipe in the discharge line is 200 m. Assume the entrance from reservoir 1 is through a square-edged inlet and that the elbows are 90° standard. The valve is fully open globe valve. A) List the piping systems components B) Generate...
1.por - + 2 Fit to page ID Page Exercise 1 (15 marks) Water at 20° flows in pipeline system shown below (Fig.1) at rate of 32400 l/hr. Pipe 1 is 15m long and 0.044 m outer diameter and pipe 2 is 100m long and 0.034m outer diameter. The thickness of both pipes is 2mm. Pipe 1 is a ductile iron uncoated pipe and pipe 2 is ductile iron coated pipe. There are totally 4 elbows in the system (two...
Water at 160° Fis drawn at the rate of 400 gal/min from a vented tank into the 2-in Sch 40 suction line of the pump made of steel. The suction line has a total length of 10 ft. the discharge line elevates the water 30 ft to the level of the large heat exchanger. The discharge line has a total length of 40 ft. The system contains: 2 standard elbows, 1 swing check valve, and 4 open gate valves. Assuming...
1 A pump delivers water from the lower reservoir to the upper reservoir at a rate of 60 L/s. Both the suction and discharge pipes are DN 150 schedule 40steel pipe. The length of the suction pipe leading to the pump is 3.5 m, and 7 m of discharge pipe extend from the pump outlet to the upper tank. There are three standard 900 elbows and a fully open gate valve. The depth of the fluid level inside the lower...
The system below shows a simplified schematic of an oil transfer system between tanks, from left to right: L L The oil specific gravity is 0.77 and its viscosity is 2.7 [cP). The pipes are horizontal and coaxial (neglect difference in height between suction and discharge). The tanks are closed but vented so that they are at atmospheric pressure ([atm]). Assume for simplicity that the liquid level in each tank is 2.5 (m) above the level of the pipes (in...
Please solve a,b,c,d,e,f
1) A water fountain is to be installed at a remote location by attaching a cast iron pipe directly to a water main through which water is flowing. The entrance to the pipe is sharp-edged 15m (K-0.5), and the 15m long piping system involves three 90 bends without vanes (K1.1), a fully open gate valve (K.-0.2), and a fully open angle valve (K-5). If the diameter of the pipe is 2 em and the system is to...
Question 1 50 marks Part A (30 marks) In a proposed water supply system, two large reservoirs will be connected with a pipeline 9 km long and with an elevation difference of 72 metres between the full water levels of the reservoirs. The pipe will be required to convey a minimum discharge of 450 L/s. The proposed pipe material is UPVC. Fittings in the pipeline include one 90° short radius elbow and one gate valve fully open. Pipeline entrance and...
A pump transports water from Tank 1 to Tank 2 through a constant-diameter piping system as shown below (not to scale). The flow rate is controlled by two gate valves, the gate valve I controls the main pipeline, while the gate valve II controls the loop line from T-joint A to T-joint B. All pipes are galvanized steel pipe of diameter D = 4 in. It has a total length of Li2= 620 ft from tank 1 to tank 2....
Most questions answered within 3 hours.
-
Please create a statement of values for a present wrapping
company.
asked 12 seconds from now -
1. Organizational buyers include all buyers of a product
except which?
government agencies
wholesalers
not-for-profit organizations...
asked 35 seconds ago -
Y = C + I + G + NX (1)
C = α + β(1 −...
asked 2 minutes ago -
A 20 bbl kick enters a 12,000 ft well containing 12 ppg mud(see
accompanying diagram for...
asked 5 minutes ago -
Alleles of the gene that determines seed coat pattern in lentils
exhibit the following
dominance series:...
asked 21 minutes ago -
You can earn 6% p.a. interest on your money (compounded
monthly). You wish to purchase a...
asked 25 minutes ago -
State some survival and important materials needed to be taken
onto the Moon by a group...
asked 21 minutes ago -
There is a tendency for economic profit in all competitive
industries to go to zero.
Question...
asked 23 minutes ago -
When a certain 1.5-V battery is used to power a 3-W flashlight
bulb, it is dead...
asked 31 minutes ago -
In this laboratory exploration various reactions of copper will
illustrate these properties. First, begin with copper...
asked 33 minutes ago -
All of these questions are related to my intro to pharmacy
class, these are pharmacy questions...
asked 34 minutes ago -
With systematic sampling, there is the risk that the person
selecting the next member for the...
asked 36 minutes ago