Steam expands through a well-insulated turbine from inlet conditions 300c and 4 Mpa with negligible velocity to exit conditions 40m/s and 0.075Mpa. The turbine is operating at steady state and has an exit diameter of 0.6Mpa. Select two different values of exit quality in the range of 0.2 to 0.5 and subsequently plot the power generated by the turbine in kw
Please Rate,
Thank you!!!
Steam expands through a well-insulated turbine from inlet conditions 300c and 4 Mpa with negligible velocity...
steam expands through a well insulated turbine from inlet condition 300c and 4Mpa with negligible velocity to exit condition 40m/s and 0.075Mpa. The turbine is operating at steady state and has an exit diameter of 0.6m. select 2 different values of exit quality in the range of 0.2 to 0.5 and subsequently plot the power generated by the turbine in kW
Question 3 Steam expands through a well-insulated turbine from inlet conditions 300°C and 4 MPa with negligible velocity to exit conditions 40 m/s and 0.075 MPa. The turbine is operating at steady state and has an exit diameter of 0.6 m. Select two (2) different values of exit quality in the range of 0.2 to 0.5 and subsequently plot the power generated by the turbine in kW. (10 MARKS]
A steam turbine, as shown in Figure Q3, operates at steady state with inlet conditions of Pi= 2 MPa, T1 = 480°C and producing 4000 kW. Saturated steam leaves the turbine at a pressure of 0.1 bar where it is condensed at 45.81 °C in the condenser. There is no significant heat transfer between the turbine and the condenser and their surroundings, and kinetic and potential energy changes between inlet and exit are negligible. A steam turbine, as shown in...
Problem 2 (30 pts) team enters a well-insulated turbine operating at steady state with a mass flow rate inlet conditions of the steam are 80 bar, 480°C, and 75 m/s, and the exit conditions are quality, and 40 m/s. The elevation of the inlet is 5 m lower than at the exit. (a) (20 points) the power developed by the turbine, in kW (b) (10 points) the turbine inlet area in em2. Here, I m 100 cm of 5760 kghr....
Steam flows steadily through an adiabatic turbine. (c) BY-NC- Niel Crews, 2013 The inlet conditions of the steam are: pressure = 10 MPa temperature = 450 °C velocity = 80 m/s The exit conditions are: pressure = 10 kPa quality = 0.92 velocity = 50 m/s a) What is the temperature of the fluid at the turbine exit? b) What is the power output of the turbine, per unit mass of the working fluid?
Steam expands isentropically in a turbine from an inlet condition of 6 MPa and 400 °C to a exit pressure of 100 kPa. The exit temperature of the steam is A. 99.61 °C B. Approximately 200 °C C. Approximately 150 °C D. 250 °C
Steam expands isentropically in a turbine from an inlet condition of 6 MPa and 400 °C to a exit pressure of 100 kPa. The exit temperature of the steam is O A. 99.61 °C B. Approximately 200 °C OC. Approximately 150 °C OD. 250 °C
Problem 3 Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 10 MPa, 400 C, and 80 m/s, and the exit conditions are 10 kPa, 92 percent quality, and 50 m/s. The mass flow rate of the steam is 12 kg/s. Determine (a) the change in kinetic energy, (b) the power output, and (c) the turbine inlet area. Pi = 10 MPa 7, = 400 °C V1 80 m/s No STEAM 3 12 kg/s ▼Sh...
Question 38 (2 points) A steam turbine receives 10 kg/s of superheated steam at 120 bar and 600°C. The steam expands adiabatically through the turbine and exits at a pressure of 0.2 bar and a quality of 90%. The steam inlet velocity is 200 m/s and the exit velocity is 50 m/s. Determine the power output of the turbine. 12.531 kW e) 12,344 kW (0) 12,719 kW None of the above
Question 4 Liquid water enters a feedwater heater at inlet 1 with inlet conditions 15 MPa, 40°C at 60 kg/s. Another stream of water in saturated mixture enters the heater at inlet 2 at temperature of 175 °C. The heater operates at steady state and heat transfer to surrounding can be neglected. At exit 3, saturated liquid flows out at 275 kPa. Select two (2) different values of mixture quality at inlet 2 between 0.5 and 0.8, and subsequently plot...