2) [30 pts] C-clamp with handle, power screw For the C clamp shown, a force is...

Question

Question

Answer 1

Answer #1

1 Solo d Here, da 0.375 in L = 3.7 in

lan Yielding Stren, Stren, Oy Oy - My 2 °។ (PXL) x ( ) CE) .bu oya 32 PL Td² where, P = force Applied at the end of handle 3.

end op the handle to reach the point of yelding 3 of the handle is 56.034 lbfi 1b ) het W be the clamping force Then , .) +

4 2T ... W= d tan co-x) 2x 23.055 W = (0.375X0.025 ) tam (29-8.531) Wa 13 176.587 N Wt 132 13176587 lof u 448 Wa 2962.36 lbf

Answer 2

Similar Homework Help Questions

For the screw clamp shown, a force is applied at the end of the handle 3...

For the screw clamp shown, a force is applied at the end of the handle 3 in from the screw centerline. The 큼 in diameter handle is made of cold-drawn AISI 1006 steel. The screw is in-10 UNC and is 8 in long, overall. The maximum possible length of screw in the clamping region is 6 in. (a) What screw torque will cause the handle to bend permanently? (b) What clamping force will the answer to part (a) cause if...
2. The C clamp shown in the figure below uses an Acme thread screw. The screw...

2. The C clamp shown in the figure below uses an Acme thread screw. The screw has a diameter of 17 mm and a pitch of 5 mm. The frictional coefficients are 0.15 for the threads and 0.20 for the collar. The collar, which in this case is the anvil striker's swivel joint, has a friction diameter of 25 mm. Find the clamping force if 105 N force applied to the handle at a distance of 100 mm from the...
For the screw clamp shown, a force is applied at the end of the handle 3...

For the screw clamp shown, a force is applied at the end of the handle 3 in from the screw centerline. The 큼 in diameter handle is made of cold-drawn AISI 1006 steel. The screw is in-10 in (a) What screw torque will cause the handle to bend permanently? er to part (a) cause if the thread friction is 0.15? (c) What clamping force will cause the screw to buckle? (d) Are there any other stresses or possible failures to...

Look at the attached question, thanks. (final answers provided) A screw clamp similar to the one...

Look at the attached question, thanks. (final answers provided) A screw clamp similar to the one shown in the figure has a handle with diameter 3/16 in made of cold-drawn AISI 1006 steel. The overall length is 4.25 in (not needed) The screw is 3/4 in-10 UNC and is 8 in long. Distance A is 3 in. The length of the handle is 4.1875 in (not needed) The clamp will accommodate parts up to 6 in high. The screw has...
in 5. The following data apply to the C-clamp: a. The screw is ACME with %...

in 5. The following data apply to the C-clamp: a. The screw is ACME with % " Diameter b. Coefficient of thread friction c. Coefficient of collar friction = 0.2 d. Mean collar radius = 0.4 in. e. Max. clamping force 1200 lb Determine: =0.12 The tightening torque The operator force at the end of the handle (Note: Use table 8-3 to determine the screw pitch (p)) (5 points)
34 in The following data apply to the C-clamp: The screw is ACME with % "...

34 in The following data apply to the C-clamp: The screw is ACME with % " Diameter b. a. Coefficient of thread friction- 0.12 Coefficient of collar friction- 0.2 d. Mean collar radius-0.4 in. e. Max. clamping force 1200 lb Determine: The tightening torque The operator force at the end of the handle c. (5 points) (Note: Use table 8-3 to determine the screw pitch (p))

The C-clamp shown in Fig. 2 uses a double threaded square screw with minor diameter 32...

The C-clamp shown in Fig. 2 uses a double threaded square screw with minor diameter 32 mm and pitch of 4 mm. The frictional coefficients are 0.2 for the threads and 0.15 for the collar. The collar has a friction diameter of 50 mm. i. Determine the maximum force P to be applied to the handle at a radius 5 cm from the screw centreline if the clamping force is F-50 N Evaluate whether self-locking occurs. ii. 5 cm
A compressive force of 450 N is to be applied to the two boards in the grip of the C clamp shown ...

A compressive force of 450 N is to be applied to the two boards in the grip of the C clamp shown in Figure 13. The threaded screw has a mean diameter of 12 mm and advances 2.8 mm per turn. The coefficient of static friction is 0.20. Neglecting any friction at point A Determine the force F which must be applied to the handle at C in order to i. Tighten the clamp to provide the clamping force. ii....
as shown in F (6 pts) Calculate F, needed for the clamping force For the screw...

as shown in F (6 pts) Calculate F, needed for the clamping force For the screw clamp shown below,a fore F,is applied at in-10 UNC. The collar friction is negete the end of the handle 3% in from the lang, bloka, a" shown in fipre (b). The screw is % gure (a), to as shown in Figure (c3, to be 30 ThE. clamping force (8-1) Fd π.fa_-1 т, = (8-2) o 0730 0.0860 0 003 70 0003 0.004 87 004...