A compressive force of 450 N is to be applied to the two boards in the grip of the C clamp shown ...

Question

Question

A compressive force of 450 N is to be applied to the two boards in the grip of the C clamp shown in Figure 13. The threaded s

Answer 1

Answer #1

tan(02) 12 1100 ny tnegu4ะ.pxch n taml b. dora steguinad dor )-4Gx12 tun! II. 31-3R). C63 N.mo (İ) 3569 N

Answer 2

Similar Homework Help Questions

2) [30 pts] C-clamp with handle, power screw For the C clamp shown, a force is...

2) [30 pts] C-clamp with handle, power screw For the C clamp shown, a force is applied at the end of the 0.375 in diameter handle. The screw is a 0.75 in-6 Acme thread (from Figure 8-3), and is 10.4 in long overall, with a maximum of 8 in possible in the clamping region. The handle and screw are both made from cold-drawn AISI 1006 steel. The coefficients of friction for the screw and the collar are 0.15. The collar,...
2. The C clamp shown in the figure below uses an Acme thread screw. The screw...

2. The C clamp shown in the figure below uses an Acme thread screw. The screw has a diameter of 17 mm and a pitch of 5 mm. The frictional coefficients are 0.15 for the threads and 0.20 for the collar. The collar, which in this case is the anvil striker's swivel joint, has a friction diameter of 25 mm. Find the clamping force if 105 N force applied to the handle at a distance of 100 mm from the...
If the clamping force on the pipe is 900 N, determine the horizontal force that must...

If the clamping force on the pipe is 900 N, determine the horizontal force that must be applied perpendicular to the handle inorder to loosen the screw. The single square-threaded screw has a mean diameter of 24 o mm and a lead of 4 mm. The coefficient of static friction is Hs 0.3. (Note: The screw is a two-force member since it is contained within pinned collars at A and B.) [Hint: Start with a FBD of member ED.] 4....

For the screw clamp shown, a force is applied at the end of the handle 3...

For the screw clamp shown, a force is applied at the end of the handle 3 in from the screw centerline. The 큼 in diameter handle is made of cold-drawn AISI 1006 steel. The screw is in-10 UNC and is 8 in long, overall. The maximum possible length of screw in the clamping region is 6 in. (a) What screw torque will cause the handle to bend permanently? (b) What clamping force will the answer to part (a) cause if...
The C-clamp shown in Fig. 2 uses a double threaded square screw with minor diameter 32...

The C-clamp shown in Fig. 2 uses a double threaded square screw with minor diameter 32 mm and pitch of 4 mm. The frictional coefficients are 0.2 for the threads and 0.15 for the collar. The collar has a friction diameter of 50 mm. i. Determine the maximum force P to be applied to the handle at a radius 5 cm from the screw centreline if the clamping force is F-50 N Evaluate whether self-locking occurs. ii. 5 cm
For the screw clamp shown, a force is applied at the end of the handle 3...

For the screw clamp shown, a force is applied at the end of the handle 3 in from the screw centerline. The 큼 in diameter handle is made of cold-drawn AISI 1006 steel. The screw is in-10 in (a) What screw torque will cause the handle to bend permanently? er to part (a) cause if the thread friction is 0.15? (c) What clamping force will cause the screw to buckle? (d) Are there any other stresses or possible failures to...

as shown in F (6 pts) Calculate F, needed for the clamping force For the screw...

as shown in F (6 pts) Calculate F, needed for the clamping force For the screw clamp shown below,a fore F,is applied at in-10 UNC. The collar friction is negete the end of the handle 3% in from the lang, bloka, a" shown in fipre (b). The screw is % gure (a), to as shown in Figure (c3, to be 30 ThE. clamping force (8-1) Fd π.fa_-1 т, = (8-2) o 0730 0.0860 0 003 70 0003 0.004 87 004...