If the unbarced length of a beam is so large, then the beam is fall in...

Question

Question

Answer 1

Answer #1

With respect to the Lateral Buckling of Beams, the beams fall under three zones as follows:

a) Zone 1

b) Zone 2

c) Zone 3

The conditions for these zones are mentioned briefly below:

Zone 1

Zone 2

Zone 3

From the above statements, it is clear that if the unbraced length of beam is so large, the beam falls in zone 3

Answer: option d: Zone 3

Add a comment

Answer 2

Similar Homework Help Questions

Calculate the fall length for a factor 0.4 fall if the rope length is 7 m....

Calculate the fall length for a factor 0.4 fall if the rope length is 7 m. Select one: a. 3.4 m b. 0.93 m c. 2.8 m d. 3.50 m
M 3: (20 points) Design the stirrup spacing for the beam shown below. Change your design between ...

m 3: (20 points) Design the stirrup spacing for the beam shown below. Change your design between Zones 1, 2, and 3 of the beam length, using a uniform spacing in each zone. Ignore the self-weight of the beam. Loads on the beam are service loads so load factors must be applied according to ACI 318 (subscripts "d" and T" denote dead and live loads, respectively). Material strengths are fe 4,0oo psi and fy 60,000 psi. The total factored shear...
Consider a wooden beam of length L 20 meters. The beam is initially standing straight up,...

Consider a wooden beam of length L 20 meters. The beam is initially standing straight up, but then a wind gust blows it enough to make it fall. Calculate the angular velocity of the beam when it hits the ground. (See figure below) top A. Cannot be determined O B. 0.858 rad/s о с. 1.213 radis D. 1.471 rad/s

A large bell is hung from a wooden beam so it can swing back and forth...

A large bell is hung from a wooden beam so it can swing back and forth with negligible friction. The center of mass of the bell is 0.55 m below the pivot, the bell has mass 40.0 kg , and the moment of inertia of the bell about an axis at the pivot is 20.0 kg⋅m2 . The clapper is a small, 1.8 kg mass attached to one end of a slender rod that has length L and negligible mass....
A person of mass m is standing on a beam one third of its length from...

A person of mass m is standing on a beam one third of its length from the beam's left end. The beam is meanwhile supported by two pylons, one at the left edge of the bea and one two-thirds of the its length from the left edge. (1/3)L (2/3)L What is the force exerted on the beam by the left pylon (shaded gray)? (½m + ¼M)g O (¼m - ½M)g O (m – M)g O (½m - ¼M)g (m +...
Constants Part A A large bell is hung from a wooden beam so it can swing...

Constants Part A A large bell is hung from a wooden beam so it can swing back and forth with negligible friction. The center of mass of the bell is 0.80 m below the pivot, the bell has mass 33.0 kg, and the moment of inertia of the bell about an axis at the pivot is 15.0 What should be the length L of the clapper rod for the bell to ring silently-that is, for the period of oscillation for...

3. Given a. W27X84 A992 Steel beam is simply supported over a 25' FT beam length. b. The compress...

Steel Design 3. Given a. W27X84 A992 Steel beam is simply supported over a 25' FT beam length. b. The compression flange of the beam is fully braced along the beam length. c. A uniformly distributed service dead load of 2.5 KLF. d. A uniformly distributed service live load of 3.5 KLF. e. A live load deflection limit of L/360. A dead live load deflection limit of L/240. f. Neglect the self-weight of the beam in all calculations. Determine: The...
Question 20 A beam has length L from A to C. It has supports at A,...

Question 20 A beam has length L from A to C. It has supports at A, B, and C as shown. Roller B is located at the middle of the beam. The beam has a constant size and material from A to C. 9 B L/2 1/2 The vertical reaction at roller B is most nearly... O 59L18 Roller B sees no vertical reaction because the beam is statically indeterminate O 3qL/4 O qL/2
A beam has length L from A to C. It has supports at A, B, and...

A beam has length L from A to C. It has supports at A, B, and C as shown. Roller B is located at the middle of the beam. The beam has a constant size and material from A to C. 9 с В 1/2 U12 ZI The vertical reaction at roller B is most nearly... OqL/2 Roller B sees no vertical reaction because the beam is statically indeterminate O 59L/8 O 3qL/4

A beam has length L from A to C. It has supports at A, B, and...

A beam has length L from A to C. It has supports at A, B, and C as shown. Roller B is located at the middle of the beam. The beam has a constant size and material from A to C. с 1/2 1/2 The vertical reaction at roller B is most nearly... Roller B sees no vertical reaction because the beam is statically indeterminate 59L/8 qL/2 O 3qL/4