The Y parametre are calculated by applying 2port networks analysis and it is given below for each circuit.
Current division rules are used for calculating parameters and no where KVL and KCL applied.These are perfectly correct.
If you have any doubt please ask in comment and give me a thumbup thanq.
please do not use the kvl and kcl to find the equation, use the Y11 .....
Problem 3 Determine the y parameters of the circuits below. 1Ω 30Ω 1Ω 30Ω 1Ω 30 Ω 2Ω 40 Ω 40 Ω ΑΛΜ 1Ω 3Ω 40 Ω 4Ω 40 Ω 30 Ω
Problem 4 Determine the hybrid parameters of the circuits below. 1Ω 30 Ω 1Ο 30Ω 1Ω 30 Ω 2Ω 40 Ω 40 Ω 1Ω 3Ω 40 Ω 4Ω 40 Ω ΑΛΛΑ 30 Ω
Problem 5 Determine the hybrid parameters of the circuits below. 30Ω 1Ω 1Ω 30Ω 30 Ω 1Ω M 2Ω 40 Ω 40 Ω 1Ω 3Ω 40 Ω 4Ω 40 Ω 30 Ω
3-3: Use KVL/KCL and Ohm's Law as needed to find the values of v1 and v2. You must show separate KCL and KVL equations, no credit will be given if other methods such as nodal analysis are used. 80 80 Ω υ,Σ 120 Ω V140 6 A
PLEASE do NOT answer using mesh analysis. Just follow the questions steps and use KCL and KVL. This question specifically wants no mesh analysis. Determine the magnitude and polarity of the voltage across the 50 ohm resistor, using Kirchoff's Voltage Law and Kirchoffs Current Law. 3. 20 Ω 10Ω W エト 2 50 Ω 20 V 40 V 30 40n
4. Find in the circuit below if V = 4/0° VAMS- Note: use KVL, KCL, and Ohm's Law to solve. {0.52 WM 5. Determine the average power and complex power supplied by the source, V , in problem 4.
I can use kcl to obtain Voc values. I am trying to get isc using kvl interpretation. To save Zth. But when I set up the kvl equation and I solved it, it didn't work out. How can I get an isc value using kvl? Problem chapter 9 QE 33 23 45 m 12L0 (I D620 13= -3210 mesh1 (3+5) I, -3; 22=6 mesha - 3; [ 1 + (4+3)) I 2 =6. (3+5)) -3; o 7567 -3 413) o...
PLEASE HELP! Jan. 31, 2018 Name: Section: I. Consider the circuit shown in figure (a) Write the mesh-current equations (b) Write the for the circuit. D。~of SOL the circuit DO NOT SOLVE shown in figure 2. The sinusoidal source is the circuit to the frequency domain er the circuit (a) Transto with the mesh-current method to find thement (b) Use phasors with the mesh (c) Find the average power absorbed source is 、dt) = 2 sin (100t + 90") volts....
please DO NOT use mesh analysis for it I need Z11 .. Z22 and just use the formula , thanks Problem 2 Determine the z parameters of the circuits below. 202 WWW O 102 AMM 322 49 WW
Please answer this electrical circuits question correctly Chapter 8, Problem 8.099 Use mesh analysis to find Vo in the circuit shown in the figure below 3Ω 20 -j30 1 2Ω Enter (a) the amplitude and (b) the phase angle. The phase angle must be in the interval (-180 1801 degrees LINK TO TEXT Bv accessing this Question Assistance, you will learn while you earn points based on the Point Potential Policy set by your to search