The upper surface of a 60-cm-thick solid plate (k = 237 W/m-K) is being cooled by...
The upper surface of a 60-cm-thick solid plate (k = 237 W/m.K) is being cooled by water with temperature of 20°C. The upper and lower surfaces of the solid plate maintained at constant temperatures of 60°C and 120°C, respectively. Given: The thermal conductivity of the solid plate is given as k = 237 W/ mK. (T..+) The thermal conductivity of water at the film temperature of T, = =(60°C + 20°C)/2 = 40°C is kfluid = 0.631 W/mK. 1. value...
The upper surface of a 60-cm-thick solid plate (k = 237 W/m.K) is being cooled by water with temperature of 20°C. The upper and lower surfaces of the solid plate maintained at constant temperatures of 60°C and 120°C, respectively. Given: The thermal conductivity of the solid plate is given as k= 237 W/m.K. (T1+T) The thermal conductivity of water at the film temperature of Tf =(60°C + 20°C)/2 = 40°C is kfluid = 0.631 W/m.K. = 2 1. value: 3.00...
1 answer & continue > The upper surface of a 60-cm-thick solid plate (k = 237 W/m-K) is being cooled by water with temperature of 20°C. The upper and lower surfaces of the solid plate maintained at constant temperatures of 60°C and 120°C, respectively. Given: The thermal conductivity of the solid plate is given as k = 237 W/mK. The thermal conductivity of water at the film temperature of T; = (1,1770) =(60°C + 20°C)/2 = 40°C is kfluid =...
5. The upper surface of a metal plate is being cooled with parallel airflow while its lower surface is subjected to a uniform heat flux of 810 W/m². The air has a free stream velocity and temperature of 2.5 m/s and 15°C respectively. Given: The properties of air: k = 0.02588 W/m-K, v = 1.608 x 10-9 mʻls, and Pr = 0.7282. Determine the surface temperature of the plate at x = 1.5 m from the leading edge. [10 Marks)...
During its manufacture, plate glass at 600°C is cooled by passing air over its surface such that the convection heat transfer coefficient is h. To prevent cracking, it is known that the temperature gradient must not exceed 15 °C/mm at any point in the glass during the cooling process. The thermal conductivity of the glass is 1.4 W/mK and its surface emissivity is 0.75. The temperature of the air that is used for the cooling is 315 °C. Assume that...
A 5-cm-diameter shaft rotates at 4500 rpm in a 15-cm long, 8-cm-outer-diameter cast iron bearing (k =70 W/m.K) with a uniform clearance of 0.6 mm filled wwith tubricating oil (u 0.03 N.s/m2 and k 0.14 W/m.K). The bearing is cooled externally by a liquid, and its outer surface is maintained at 40°C. Disregarding heat conduction through the shaft and assuming one- dimensional heat transfer, determine (a) the rate of heat transfer to the coolant, (b) the sutacs temperature of the...
Question 7 10 points Hot carbon dioxide exhaust gas at 1am is being cooled by flat plates. The gas at 220°C flows in paralel over the upper and lower surfaces of a 2 m long flat plate at a velocity of 2.7 ms and the fat plate surface temperature is maintained at 80°C Determine the heat transfer coefficinth in wim?c for the following conditions Re Number - 414.117.86 Thermal conductivity k 0.02652 Prandel Number Pr 0.8292
Heat transfer question. A large wall made of 10-cm-thick solid brick (k = 0.8 W/m.K, p 2000 kg/m3, and p 800 J/kg.K) is originally at a uniform temperature of 30°C. The wall is adiabatic (well insulated) on one side as shown in the figure. The other surface is suddenly exposed to convection air flow at 10°C, resulting in a heat transfer coefficient h=40W/m2.K. Fluid (4.1) Determine the temperature of both surfaces Gr 0 and x 10 cm) after 5 hr...
A hot brass plate is having its upper surface cooled by impinging jet of the air at temperature of 15 oC and convection coefficient of k=180, 190, 200, 210 220 and 230 W/m2 oK. The 20-cm wide and 10-cm length brass plate (ρ=8530 kg/m3, and Cp=380 J/kg K. k=220 w/mK had a uniform initial temperature of 650 oC, and lover surface of the plat is well insulated. Using uniform node for Δx = Δy = 2.5 cm and left side...
Problem 1 (20 marks): A 1-m x 1-m surface at 100 °C is to be cooled by attaching to it 5-cm long, 0.25- cm-thick square aluminum fins (k = 237 W/m- K), with an edge-to-edge distance between the fins of 0.25 cm. The temperature of the fin tip is the same as surrounding medium at 30°C, und the heat transfer coefficient on the surfaces is 35 W/m2 K. Determine: temperature at distance of 2 cm away from the base the...