SOLUTION-
IF YOU HAVE ANY DOUBT PLEASE COMMENT DOWN BELOW I WILL
SOLVE IT FOR YOU:)
----------------PLEASE RATE THE ANSWER-----------THANK
YOU!!!!!!!!----------
2. (a) An 8-bit A/D converter has an input range of 0 to 15 V and...
2. (a) An 8-bit A/D converter has an input range of 0 to 15 V and an output in simple binary. Find the output (in decimal) if the input is (a) 6.42 V (b) -6.42 V (c) 12 V (d) OV (b) Convert Hexa decimal Number B602 to a decimal number and Binary. Convert decimal number 227 to binary number.
A 12 bit A/D converter has an input range of -12 V to 12 V. An amplifier is connected to the input and has selectable gains of 10, 25, 50, 100, 250, and 500. The connected transducer has an output that varies between +75 and -75 mV. Design a simple voltage-divider attenuator using standard resistor values to minimize the quantizing error. What will the quantizing error be when the transducer voltage is 5 mV.
A 12-bit A/D converter has an input range of ±8 V. Determine the step size. Do this by hand and show all work.
1. An A/D converter will convert voltages over a 0 to 10 V range. How many bits must it be to achieve a 1 mV resolution over the entire range? 2. You have an A/D converter that will convert over a range of 0 to 5 V. You input an analog signal to it that has a range of 1 to 3.5 V. What must be the number of bits of the converter to achieve a resolution of 1% of...
Problem For an 8 bit-Unipolar D/A converter, what is the output voltage for an input of E8h? Assume that the reference voltage is 10V? For a 10 bit-Bipolar D/A converter, what is the input binary code for an output voltage of -3.5V? Assume that the reference voltage is 12V? problem Determine how many bits a D/A converter must have to provide output increments of 0.03V or less? Assume that the reference is 10V. What is the exact percentage of change...
8 (8 points) A 6-bit successive approximation A/D conversion has an input range of 0 to 10 v For an input signal of 6 V, show the The final bit values are (from MSB to LSB) conversion process in the following block. 10 7.5 2.5 0
When designing an Analog to Digital System all of the range values for the system must be defined from input to output. This input will be used to drive a 3. PWM output signal to operate an LED. Assume the PWM is calibrated to read minimum to maximum based on the binary input range given. Potentiometer - 10 KS2 (0 degrees to 180 degrees) VDC for Potentiometer 12 V Analog Converter Module 10 bit, Vref 8 V PWM Module-8 bit,...
An 8-bit D/A converter with a 10-volt reference (and Rf = R) has an input of 10010001. What is the output voltage? What is the step size of the D/A converter? What is the percent resolution?
(b) Convert the numbers +26 and -26 to 2's-complement 8-bit simple binary. Tukar nombor-nombor perpuluhan +26 dan-26 kepada pelengkap 2 's perduaan mudah &-bit] (3 Marks/Markah) (c) The most common type of analog-to-digital (A/D) converter used in computerized data-acquisition system is the successive-approximations, which employs an interval-halving technique. Consider a 12-bit A/D unipolar successive-approximations converter, which has an input range of 0 to 10 V. An analog voltage of 3.29 V is applied to the A/D input. Simulate the successive-...
(a) Write a truth table. The input is 4-bit binary ABCD, A is MSB, D is LSB. The output is also represented by x. (b) Obtain an output expression in the form of a SOP. (c) Use Boolean Algebra to design a circuit consisting of only four inverters, four 3-input and gate, and one 4-input OR gate using the simplified and simplified expression obtained in (b). 4-6. The Excess-3 coding system is a four-bit digital coding system for encoding all...