Question

Plate (30pts) A steady-state oil jet coming out of a nozzle with diameter D = 10 cm at a velocity of 8 m/s strikes a circular
0 0
Add a comment Improve this question Transcribed image text
Answer #1

Specific gravity af oil V İŞG ) oil 0.82 Dj=locm LL Vj = 8m/ee flow rate of oil 2 V. control volume 4 Dy of oil yet Stoicking

Add a comment
Know the answer?
Add Answer to:
Plate (30pts) A steady-state oil jet coming out of a nozzle with diameter D = 10...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • Please solve both with showing steps 5.29. A 4.0-cm diameter nozzle delivers a jet of water...

    Please solve both with showing steps 5.29. A 4.0-cm diameter nozzle delivers a jet of water that strikes a flat plate normally. If the water speed is 50.0 m/s, calculate the force acting on the plate if (a) the plate is stationary. 5.32. A 4-in-diameter nozzle is fitted at the end of a 10-in diameter pipeline, as shown in Figure P5.32. The pressure at the end of the pipe (nozzle inlet) is 20 psi and at the nozzle exit the...

  • 1 (a) A steady stream of water jet discharges from the nozzle with a uniform velocity...

    1 (a) A steady stream of water jet discharges from the nozzle with a uniform velocity of 10 m/s at angle 60° as shown in Figure 1. The jet strikes a horizontal plate 2 m above the nozzle exit. Upon impact, part of the flow is guided towards the left while the remainder towards the right, and the plate is suspended in the air. The weight of the plate is 25 N. Assume frictionless flow along the plate and weight...

  • III A horizontal 4-cm-diameter jet of water strikes a vertical plate. Determine the velocity issuing from...

    III A horizontal 4-cm-diameter jet of water strikes a vertical plate. Determine the velocity issuing from the jet if a force of 700 N is needed to 1) Hold the plate stationary 2) Move the plate away from the jet at 8 m/s

  • 4. A water jet with a velocity of 20 m/s impacts on a splitter plate 50...

    4. A water jet with a velocity of 20 m/s impacts on a splitter plate 50 cm so that 1/5 of the water is deflected toward the bottom and 4/5 toward the top. The angle of the plate is 45 degree. Determine the force required to hold the plate stationary. Neglect the weight of the plate and water, and neglect viscous effects. A 0.1 m2 45°

  • Name: CHE 231: Fluid Mechanics Individual assignment #2 1. Ethanol at 20 °C flows through a...

    Name: CHE 231: Fluid Mechanics Individual assignment #2 1. Ethanol at 20 °C flows through a circular nozzle, exits into the air as a jet, and strikes a plate, as shown. The force required to hold the plate steady is 28 N. Assuming steady flow, estimate the mercury (S = 13.55) manometer reading, h (in cm). **Manometer is not drawn to scale. Di = 10 cm D2 = 3 cm F Air h? Hg

  • 8. In Fig. FE3.1 water exits from a nozzle at steady state into atmospheric pressure of...

    8. In Fig. FE3.1 water exits from a nozzle at steady state into atmospheric pressure of 101 kPa. If the flow rate is 160 gal/min, what is the average velocity at section 1? 1 gal- 3.7% 103 me. (5 pts) 7 cm 4 cm jet (b) 0.81 m/s (c) 93 m/s (d) 23 m/s (a) 2.6 m/s (e) 1.62 m/s P 101 kPa Fig. FE3.1 9. A fireboat pump delivers water to a vertical nozzle with a 3:1 diameter ratio,...

  • It's Mechanic Fluid subject! Please, solve them with clear handwriting and make sure it's 100 %correct!...

    It's Mechanic Fluid subject! Please, solve them with clear handwriting and make sure it's 100 %correct! Thanks! 8. Crude oil of specific gravity 0.82 and viscosity of 0.4 N-s/m2 is flowing at a rate of 8 ms through a pipe of diameter 0.9 m with a Darcy friction factor of 0.02. The head loss (m) due to viscous effects over 45 m of the pipe is most nearly: a. 2.0 m b. 4.0 m c. 6.0 m d. 8.0 m...

  • A water jet with a velocity of V; -8 m/s and jet diameter D; -10 cm...

    A water jet with a velocity of V; -8 m/s and jet diameter D; -10 cm impinges on a cup cavity. The water is turned 180° and exits, due to friction, at lower velocity of Ve= 4 m/s. Looking from the left, the exit jet is a circular annulus of outer radius (R) and thickness (h), flowing toward the viewer. The cup has a radius of curvature of R-10cm. Find the thickness of the exit jet (h=?cm) Oh=1.0 cm h...

  • CENTRE INDEX NUMBER SECTION B 30 marks] Calculate the discharge through a pipe of diameter 200...

    CENTRE INDEX NUMBER SECTION B 30 marks] Calculate the discharge through a pipe of diameter 200 mm when the difference of pressure head between the ends of the pipe 500 m apart is 4 m of water. Take the value off= 0.009 in the formula hl= a) 19.5e/s b)2.0es e)03 m's d) 29.3 e/s 2. A scale 1:50 scale model of ship is towed through sea water at a speed of 1 ms. A force of 2 N is required...

  • 10. Write a one-page summary of the attached paper? INTRODUCTION Many problems can develop in activated...

    10. Write a one-page summary of the attached paper? INTRODUCTION Many problems can develop in activated sludge operation that adversely affect effluent quality with origins in the engineering, hydraulic and microbiological components of the process. The real "heart" of the activated sludge system is the development and maintenance of a mixed microbial culture (activated sludge) that treats wastewater and which can be managed. One definition of a wastewater treatment plant operator is a "bug farmer", one who controls the aeration...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT