Hopefully this will clear all your doubts.If you still face any query let me know in the comment section.Thank You.
With examples, explain the two types of signals (Analog and Digital) and two types of data...
Q1 Marks: 40 A digital communication system has 96 analog telephone signals, each band limited to 4 kHz. The telephone signals are converted to digital binary data using Pulse Code Modulator (PCM) system, which use a uniform quantiser followed by an 8-bit encoder. The system uses two bits for synchronization. The digital binary data are then time-division multiplexed and transmitted over a single communication channel. Analyse the communication system by considering the following principles: (i) Determine the number of quantization...
please type the answer....No Hand writting please Two types of digital-to-analog modulation techniques are Amplitude Shift Keying (ASK) and Frequency Shift Keying (FSK). In ASK, two different amplitudes, and only two, represent the digital information. In FSK, only two different frequencies are used to represent the digital data. The Goal The goal of the design project is to design a Commsim circuit that will generate the following analog carrier based on a digital input stream: Output 2 0 -1 -2...
question 2 and 3 () Describe analog and digital signals in terms of Noise and interference tolerance 2 Marks Eachl Bandwidth m) Power consumption (iv) Impedance (b) Sute real life examples of stochastic and deterministic [3 Marks (c) Differentiate between impulse response and frequency response of an LTI system [4 Marks] Question Two Find the fourier transform of the following functions and sketch the diagrams. [3 Marks Each] O eftirect(3U4) (i) x 2recut-2) (1) y(t)=x(t)e (iv) (t)-(-3) (v) n(t)rect(t/3)*y(t)cost Question...
DILU 2d) Analog and Digital Signals i. A 10-bit linear analog-to-digital has reference voltage 3.3 V such that it operates correct. for input voltage Vin in the range 0 < Vin < 3.3 V. What is its output, in unsigned binary when Vin = 2.267 V? - ii. What is the quantisation error (in volts) for a 10-bit linear analog-to-digital converter with reference voltage 3.3 V?
3. With the aid of a diagram, briefly explain th ing principle of a Successive a) Approximation Analog-to-Digital Converter (ADC) b) An ADC has to be designed to convert voltages in the range from -5 V to +5 V, with a resolution below (better than) 1 mV. What is the minimum number of bits required to meet this design specification? An ADC has to be designed to convert input voltage signals with frequency c) components less than or equal o...
Describe Amplitude Modulation technique with a diagram (use binary data 01001100011. Draw both digital and analog signals. (2 points)
4. Explain digital-to-analog converter 5. What is a transducer ? Provide an example 6. What is an actuator? Provide an example
Provide specification and high-level design for an Analog to Digital Convector (A/D) that will allow us to achieve 96 dB Signal to Noise Ratio (SNR) and be able to digitize 10 sinusoidal signals with the highest frequency of these Sin waves to be 10 KHz. Please specify the A/D device required and show your calculations
Module 2 - Quiz 2 TRUE OR FALSE T F 1. Only digital signals can be used to convey information in the communications environment, T F 2. The greater the bandwidth of the signal the greater its information carrying capacity T F 3. The transmission media that are used to convey information can be classified as guided or unguided. T F 4. Twisted pair may only be used to transmit analog and digital signals. T F S. Both analog and...
An analog to digital converter is to be designed for a digital communication system. In this converter, the output of the sampler varies between +3V and -3V. a. Design a uniform quantizer with minimum peak signal power to average quantization noise power ratio equal to 28 dB. Draw a complete diagram of the quantizer clearly showing quantile interval and quantization levels. Show each design step in detail. Accuracy up to 4 decimal places is required. b. Using the quantizer designed...