Q6: Design an eight-way multiplexer and find the output Y when S2 S1 So=101 and D...
digital logic design 4. (10 Points) Draw the output waveform for the following 4-input multiplexer with given input waveforms. S1 SO Y 0 0 IO MUN 0 1 11 SI SO 1 0 12 1 1 Si So 13 G Search or tune TIRI
2 Design a circuit that has two inputs, clk and X, and produces one output O. Xmay change every clock cycle and the change happens at the falling edge. The circuit samples the input at every rising edge of the clock. O is 1 (for one clock cycle, from positive edge to positive edge) if the last values of X over the last three cycles were 101. (a) Complete the following the state transition diagram for this circuit. Assume that...
I am trying to find out a design containing NOR and OR or AND gate for the interface block design. I have completed a design for when A = B, but I am having difficulty designing A < B and B > A on the subtractor where the boxes have question marks. Please help! 8.3* The circuit of 8.2, configured as a subtractor, can be used to compare two 4-bit numbers. Subtractor outputs C4 and (S3..S0) can be combined logically...
5) Decoders: Given the following circuit, S0 and S1 are computed using a 4-2 priority encoder with the priorities indicated on the figure. (hint: IDLE signal is always 0, if any of the inputs 10,11,12, or 13 is 1) 6 points) 4-to-2 Priority Encoder 10 YO YI 13 IDLE 13> 11 > 12>10 12 Full c Adder So Fill the following table showing the output signals S0 and SI given the input signals w, x, y, a) and z. Prof...
H is 1.32 B is 11.03 n1 is 0.022 n2 is 0.026 S1 is 0.00176 S2 is 0.00210 PROBLEM A lake (reservoir) is connected to the rectangular channels as illustrated in the figure below. Details of the data for your design project is prepared and listed in a separate DATA TABLE you may find on Moodle. Therefore, Halid us epwall Ex fortuis reference), B, N, Sor, Mz and Saz values are given for your problem. ASKED 2. Check your slope...
Design and implement a combinational circuit with four inputs w,x, y and z and four outputs A, B ,C and D using CMOS transistors. When the binary input is 0, 1, 2,3,4,5,6 or 7 the binary output is five greater than the input. When the binary input is 8,,10,11,12,13,14 or 15 the binary output is seven less than the input. for question (a) find the troth table for the inputs (ABCD) then implement using K-map to find the equations to...
a-represent system in state space form? b-find output response y(t? c-design a state feedback gain controller? 3- A dynamic system is described by the following set of coupled linear ordinary differential equations: x1 + 2x1-4x2-5u x1-x2 + 4x1 + x2 = 5u EDQMS 2/3 Page 1 of 2 a. Represent the system in state-space form. b. For u(t) =1 and initial condition state vector x(0) = LII find the outp (10 marks) response y(t). c. Design a state feedback gain...
could you explain these equations cause i get confuse how do we get these? thanks in advance D 9.114 The two-stage CMOS op amp in Fig. P9.114 is D *9.115 In fabricated in a 0.18-μm technology having = 4 -Fig. 9.40 the increasing th of 4. Assumi (a) With A and B grounded, perform a dc design that will result in each of Q, Q2, Q3, and Q4 conducting a drain current of 100 1A and each of Q6 and...
1. A copper wire is secured between two immovable supports so that it has negligible tension at a temperature of300 The tension in the wire increases o 400N when it is cooled to100 c Find the diameter of the wire. For copper, a 1.70 x 10 c and Y 11.0x 101° Pa. (a) 2.61 mm 3.20 mm3.69mm (d) 4.13 mm (e) 4.52 mm (c))3.69 mrm 1. A copper wire is secured between two immovable supports so that it has negligible...
If anyone has Matlab, help me with problem e and f. Thank you. Design by Synthesis: It is possible to design the PID so that the overshoot of the feedback system would be zero, furthermore, the feedback system would behave as a first order system. This is done by noting the PID transfer function: 3. PID Controller Plant Gp (s) R(s) C(s) s2+s+1 Note in the above KPK and Ki/Kp may be chosen so that the numerator of the PID...