Thyristor (RL load) with AC Firing Circuit Half Wave
R=16.5
L=0.0565
α =46.5
please I want to simulate the circuit with matlab or PSIM
and load voltage graph and load current graph
and explaining why using elements
We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
Thyristor (RL load) with AC Firing Circuit Half Wave R=16.5 L=0.0565 α =46.5 please I want...
A single-phase half-wave ac voltage controller feeds a load of R = 40 Ω with (maximum voltage of 230V), 50 Hz. Firing angle of thyristor is 60°. Determine (a) rms value of output voltage (b) power delivered to load and input pf and (c) average input current. (a) The rms value of load voltage. And repeat the above for A single phase Full-wave ac voltage controller?
i want the answer with detales
Single-Phase Controlled Rectifier Exercise Derive the expressions of the average load voltage and current in single-phase half-wave controlled rectifiers and resistive load. Draw the waveforms of supply voltage. output voltage, output current, thyristor voltage and thyristor current Exercise In a single-phase half-wave controlled rectifier and resistive kad, it is desired to get an average load voltage of 80 V. Determine the firing angle if the ac supply voltage is 230 V. If the load...
A controlled half-wave rectifier has an RL load with R 20 ohm and L 40 mH. The source is 120 V rms at 60 Hz The delay angle required to produce an average current of 2.0 A I output RMS I input RMS Apparent power and power factor Skitch Vout, Iout, and V diod
Q2) A single phase half-wave uncontrolled rectifier with RL load is shown below With R-1000 L 01H w-377rad/s and V 100V, Determine a) An expression for the load current i(t). b) The value of the current at t 16 ms c) The average load current (10 marks) 7 RV そ0 -121 34.7 Vsinfwr) + VE 0.360
Q2) A single phase half-wave uncontrolled rectifier with RL load is shown below With R-1000 L 01H w-377rad/s and V 100V, Determine a) An...
i. The speed of a separately excited dc motor is controlled by a one-phase full-wave converter. The field circuit is also controlled by a full-wave converter, see V supply) Vs pk-150V Ra-0.310 L Rf 152O E-63V α. 1-35A Figure 3 The AC supply voltage to the armature and field converters is one-phase, 150Vpeak, 50Hz. The armature resistance Ra-0.31Ω, the field circuit resistance Rf-152Ω, and the motor voltage constant is Kv-1.3V/A. The armature current corresponding to the load demand la-35A The...
R-L-C circuit
Please write down clearly?
In the circuit, the AC voltage is applied to the R-L-C circuit. 10mH 100/2sin 10'r 0.2mF HH a) Find the current flowing through the circuit. Express in the instantaneous form i(t). Assume the steady state condition. (hint: use the complex impedance to calculate the current) b) Find the active power and the reactive power supplied by the voltage source.
Please answer asap with steps
In a series R-L-C circuit powered by an ac sinusoidal voltage source, which phasor diagram best illustrates the relationship between the current i and the potential drop vc across the capacitor?
please help i do not understand
lyue 2 The controlled half-wave rectifier of Figure 3 has an ac input of 120 V rms at 60 Hz, R=20 0, L= 200 mH, and Vdc =80 V. The delay angle a is 30 degrees. Determine (a) an expression for the current, (b) the power absorbed by the resistor and (c) the power absorbed by the de source in the load, R W-0001 th 1.sin(01) Vs Figure 3
Please, answer to the following questions based on the diagram
provided.
1)Why is it L/R not LR for the charging and discharging a series
RL circuit?
2) In the determination of C in part II, what will you obseve if
the voltage probe was connected across decade resistor Rd? Can you
determine capacitance from this? (During the experiment we
connected voltage probes across capacitor)
3) In the determination of L in Part III, what will you obseve
if the voltage...