Note: According to the HomeworkLib guidelines, I have posted only first question solution here in detail . kindly post rest of the question in separate post
i want the answer with detales Single-Phase Controlled Rectifier Exercise Derive the expressions of the average...
A single-phase full bridge thyristor rectifier is supplied from a 200vrm 50HZ AC source, and supplies a series R-L load comprising a 202 resistance and a 36.8mH inductance 2.a. Sketch the circuit diagram for this rectifier Q2. [4 marks] [Refer to lecture notes] 2.b. Determine the maximum possible average DC voltage that can be achieved across the load resistor [4 marks] [VDC (avg) = 180V] 2.c. Determine the SCR firing angle at which the rectified output curent will just be...
Q4: A thyristor controlled single phase rectifier as shown below. Given that input voltage Vs is 60Hz and 150V amplitude, a) calculate the phase angle needed to produce an output voltage of 20V. b) Sketch the waveforms of the output voltage with clear indication of the firing angle. c) what is the voltage rating needed for T1? ind * Eetro I
Derive the expressions of the average and rms values of the load voltage and current in three-phase uncontrolled bridge rectifiers with resistive load. Draw the waveforms of supply voltage (line-line voltages), transformer phase current (only one phase), load voltage, load current and diode current.
b. Consider the single-phase fully controlled of thyristor bridge rectifier supplies a load consists of R-L load and Vee in series as shown in Figure Q2 (b). The parameters for this circuit are as follows: supply voltage is 120 Vrms at 60 Hz, DC voltage, Voe equal to 10 v. i. Sketch the waveforms for output voltage, thyristor current, diode current and output current (CO2: PO2 - 5 marks) Calculate the output voltage, Va at a = Tt/2. (CO2: PO2...
1. A 50 Hz 3-phase Have wave uncontrolled rectifier circuit is used to supply a resistive load of 100 ohms. The supply is unbalanced and defined as v.-127.28 cos (ot) V 127.28 sin (ot-0.5236) V n63.64 cos (ot+2.0944) V a) Draw the circuit diagram. b) Draw the three phase voltages wave forms. c) Use phasor diagram or any other method to obtain the line voltages v and d) Draw the line voltages v and v wave forms. e) Derive an...
A single phase half wave controlled rectifier shown below operates from ideal sinusoidal source with vi =325sinwt at 50Hz. If the load is purely resistive, and at a certain α, the output dc voltage is Vdc =95V, and the average valu of the load current is 2.2A. It is required to calculate the following: a) The triggering angle α b) Load resistance c) r.m.s load current d) dc power is 다. Firing Circuit
Analyze a DC series phase-controlled motor drive with single-phase, full wave, controlled AC/DC rectifier in continuous conduction mode (CCM) of operation. Draw the motor voltage and current waveforms and write the equations (instantaneous and averaged). Please note that the waveforms and equations have been presented in class for a DC separately-excited motor drive.
Derive the expressions of the average and rms values of the load voltage and current in single-phase half-wave uncontrolled rectifiers. In case of practical diode, draw the waveforms of supply voltage, output voltage, output current and diode voltage.
3. A controlled single-phase fiull-wave controlled rectifier is connected in a de motor drive in Figure 4. The de motor armature inductance can be assumed large enough such that any motor curent ripple is negligible. (a) Assuming negligible supply reactance, show that the average rectifier output voltage V, in tems of the supply ms voltage E and the firing angle a, is given by 2/2E (6 marks) cos a _ (b) Given that the supply voltage is 230V, 50HZ and...
A single phase half-wave SCR rectifier is used to reduce the average voltage across a nonlinear resistive load where the resistive value is represented by R = 0. 2 V^2(aver) + 5 Ω Calculate the load average current when the source voltage is 110 V RMS and the triggering angle is 90 degrees A single phase half-wave SCR rectifier is used to reduce the average voltage across a nonlinear resistive load where the resistive value is represented by aver Calculate...