`Hey,
Note: If you have any queries related the answer please do comment. I would be very happy to resolve all your queries.
clc
clear all
close all
format long
time=5:5:60;
current=[16,25,32,40,45,47,44,40,33,26,20,11];
voltage=[2,5,4.5,4.7,5.5,5.4,4.2,3.9,3.3,3,2.8,2.1];
C1=polyfit(time,current,2);
C2=polyfit(time,voltage,2);
t=5:0.01:60;
y1=polyval(C1,t);
y2=polyval(C2,t);
plot(time,current,'or',t,y1,time,voltage,'xb',t,y2);
legend('current model','data current','voltage model','data
voltage');
disp('Voltage reached maximum at');
f=@(x) -polyval(C2,x);
t=fminbnd(f,5,60)
Kindly revert for any queries
Thanks.
The current and voltage data are recorded below every 5 seconds for 1 minute (called a...
Wat appear when half the time, 5 minutes, 1 minute and 30 seconds remain tiple Attempts Not allowed. This test can only be taken once ce Completion This test can be saved and resumed at any point until time has expired. The time will continue to run if you leave the test. emaining Time: 1 hour, 57 minutes, 42 seconds, Question Completion Status: > Moving to another question will save this response. Question 9 of 2 uestion 9 points Best...
s i automatically when the time expires all the time, 5 minutes, 1 minute, and 30 seconds remain Multiple Attempts Not allowed. This test can only be taken once Force Completion This test can be saved and resumed at any point until time has expired. The time will continue to run if you leave the test. Remaining Time: 1 hour, 45 minutes, 51 seconds. Question Completion Status: As Moving to another question will save this response. << Question 24 of...
Problem 31: (34 points) 1. (10 points) A pulse width modulated (PWM) signal fPwM(t) in Figure 2. The symbol D represents a duty cycle, a number between zero and one. Determine the compact trigonometric Fourier series coefficients (Co C,11 %) of the signal f(t). 2. (10 points) One use of PWM is to generate variable DC voltages. While the PWM signal is not DC, you should be able to see from your results in part 1 that it hss a...
A group of physics students collected data from a test of the projectile motion problem that was analyzed in a previous lab exercise (L5). In their test, the students varied the angle and initial velocity Vo at which the projectile was launched, and then measured the resulting time of flight (tright). Note that tright was the dependent variable, while and Vo were independent variables. The results are listed below. (degrees) Time of Flight (s) Initial Velocity V. (m/s) 15 20...
Short Answer 9. Suppose that you and a friend analyze the same sample data and conduct a test of significance about the same conjectured value, but you use a two-sided alternative and your friend uses a onesided alternative. a. Will you and your friend obtain different values of the test statistic? Explain briefly. b. Will you and your friend obtain different values of the p-value? Explain briefly. 10. The National Institutes of Health funded a study of a random sample of 856 people age...
#4 TEST 2, PHYS 1442. Instructor: Dr. G. Kolmakov Student Name Date: 5/1/2018 Notes: 1. Show equations you use and show your work. Answers without work shown will not be given any credit. 2. Box the final answers. 3. Show units in the answers. 4. Maximum point for the test is 100. 1. (10 points) What is the resistance of a 35-meter long wire that has a diameter of 0.812*10- m and is made of copper? The resistivity of copper...
PART I. Multiple Choice. Cirele the letter to the correct answer on the front page 1. Below is a list of assumptions necessary for the regression analysis to be valid. With each assumption is a proposed procedure (on the right) for checking the validity of the assumption. Select the assumption validity which is the correct match. a. Normal errors b. Constant error variance C. Plot of residuals versus x Plot of residuals versus x Histogram of residuals Look for outliers...
PART I. Multiple Choice. Cirele the letter to the correct answer on the front page 1. Below is a list of assumptions necessary for the regression analysis to be valid. With each assumption is a proposed procedure (on the right) for checking the validity of the assumption. Select the assumption validity which is the correct match. a. Normal errors b. Constant error variance C. Plot of residuals versus x Plot of residuals versus x Histogram of residuals Look for outliers...
The lab for this week addresses taking a logical database design (data model) and transforming it into a physical model (tables, constraints, and relationships). As part of the lab, you will need to download the zip file titled CIS336Lab3Files from Doc Sharing. This zip file contains the ERD, Data Dictionary, and test data for the tables you create as you complete this exercise. Your job will be to use the ERD Diagram found below as a guide to define the...
Please help with my car traffic simulator! Code that I already have below, I do not know how to start it off! public class IntersectionSimulation { private final static int EAST_WEST_GREEN_TIME = 30 ; private final static int[] NORTH_SOUTH_GREEN_TIMES = { 20, 24, 30, 42 } ; private final static int[] CAR_INTERSECTION_RATES = { 3, 5, 10 } ; private final static int[] CAR_QUEUEING_RATES = { 5, 10, 30 } ; private final static int[] EXPERIMENT_DURATIONS = { 3*60, 5*60,...