B Steam flows in a steel pipe, which is insulated by gypsum plaster. The inner and...
Steam at 150 °C flows in a stainless steel pipe which has a thermal conductivity of 16 W m-1 K -1 whose inner and outer diameters are 5 and 6 cm respectively. The pipe is covered with 3 cm think insulation having a thermal conductivity of 0.035 W m-1 K -1 . The combined convection and radiation heat transfer coefficient at the outside surface of the insulation is 20 W m-2 K -1 and the surroundings are at 10 °C....
A stainless pipe having an inner wall thickness of 5 cm, an outer wall thickness of 5.5 cm and a thermal conductivity of 15 W/m˚C transfers steam at 320˚C from one location to another. The pipe is insulated with a 3 cm thick glass wool having a thermal conductivity of 0.038 W/m˚C. Heat is lost to the surroundings by natural convection and radiation at a rate of 15 W/m2˚C and the heat transfer coefficient inside the pipe is 80 W/m2˚C....
art II- Show your work 17 Marks team at 320°C flows in a stainless steel pipe (kr 15 W/m "C) whose inner and outer diameters are 5 em and 5.5 cm, respectively. The pipe is covered with 3-cm-thick glass wool insulation (k 0.038 W m·°C). Heat is lost to the surroundings at 5°C by natural convection and radiation, with a combined natural convection and radiation heat transfer coefficient of hi-15 w/m.。C. The convective heat transfer coefficient inside the pipe to...
HW3.3. A cylindrical steel pipe is used to carry water steam with an averaged heat transfer coefficient of h 150 W/m2-K at Ti- 100 °C. The steel pipe goes through the roof of a factory where the ambient temperature is 23°C (To), with a natural heat convection coefficient of 5 W/m2-K. The inner and outer diameters of the steel pipe are 2 cm and 2.2 cm, respectively, and thermal conductivity of the steep pipe is k, -20 W/m-K To prevent...
I. Steam at 220°C İs transported through an AISI 101 0 carbon steel pipe. The inside and outside diameters of the pip glass pipe insulation. e are 12 and 13 cm respectively. The pipe is wrapped with 5 cm thick cellular The ambient air temperature is 8°C. The inside and outside convection heat nts are 95 and 15 W/m2-K respectively. The thermal conductivity of the pipe is 60 W/m-K and for the insulation it is 0.072 W/m-K a. Construct the...
Problem 3 (30): Steam at Too,1 340 °C flows in a cast iron pipe [k- 80 W/m.°C] whose inner and outer diameter are Di 6 cm and D2 -8 cm, respectively. The pipe is covered with a 4-cm thick glass wool insulation [k-0.05 W/ m°C]. Heat is lost to the surroundings at Too,2 - 21°C by natural convection and radiation, with a combined heat transfer coefficient of h- 18 W/m2 °C. Taking the heat transfer coefficient inside the pipe to...
A pipe with insulation material is used to carry steam to an operating plant. The conditions and dimensions for the system are as follows Variable Value Length of pipe, L 100 ft Inner diameter of pipe, Do 1 inch Outer diameter of pipe, D1 1.24 inches Outer diameter of insulation, D2 2 inches Inside film heat transfer coefficient for condensing saturated steam, ho 800 Btu/hr-ft2.oF Outside film heat transfer coefficient for air, ht 2 Btu/hr-ft2.oF Thermal conductivity of the pipe,...
Superheated steam flows steadily through steel tubing (k 35 W/m-K) applying a tube inner surface temperature of 575°C. The tubing has an inner diameter of 300 mm and a wall thickness of 30 mm. Insulation (k 0.10 W/m-K) is applied to the outer surface of the tube while thin aluminum sheet is applied around the insulation as a protective covering. The ambient air at 27°C provides a convection coefficient of 6 W/m2-K. Determine the minimum insulation thickness necessary (mm) to...
1. A ¾ inch (nominal), Schedule 40, mild steel pipe carries 40 psia steam through a room having an air temperature of 80°F. The pipe is covered with a 0.125 ft thick layer of fiberglass insulation having a thermal conductivity of 0.037 Btu/(h ft ‘F). The hi value on the steam side of the pipe is 1000 Btu/h ft2 °F. The ho value on the outside of the insulation is 2.0 Btu/(h ft2 ’F). For the mild steel, k=26Btu/(ft H...
Problem 1. (30 points) A double-pipe heat exchanger is used to condense steam at 7370 N/m2. Water at an average bulk temperature of 10°C flows at 2.50 m/s through the inner pipe. which is made of copper and has a 2.54-cm ID and a 3.05-cm OD. Steam at its saturation temperature flows in the annulus formed between the outer surface of the inner pipe and an outer pipe of 5.08-cm-ID. The average heat transfer coefficient of the condensing steam is...