Solution:
The schematic microstructures of a hypoeuctectoid steel, eutectoid steel and hypereutectoid steel and the existing phases are shown below:
Hardness: When the carbon content is increased then the hardness
is increased. Hyper eutectoid steel is having high carbon content
than eutectoid steel and hypo eutectoid steel. Therefore Hyper
eutectoid steel is having high hardness than eutectoid steel and
hypo eutectoid steel. i.e Hyper eutectoid steel
eutectoid steel
Hypo eutectoid steel.
Strength: Hardness is directly proportional to strength so the
hyper eutectoid steel is having high strength than eutectoid steel
and hypo eutectoid steel. i.e Hyper eutectoid steel
eutectoid steel
Hypo eutectoid steel.
Ductility: Hardness is inversely proportional to ductility then
hypo eutectoid steel is having high ductility than eutectoid steel
and hyper eutectoid steel. i.e Hypo eutectoid steel
eutectoid steel
Hyper eutectoid steel.
Draw schematic microstructures of a hypoeutectoid steel, eutectoid steel and hypereutectoid steel, define the existing phases...
1060 steel heated to ? region slowly cool to just above eutectoid temperature. What phases/structures are present? What is the expected hardness, BHN for the 1060 steel after (OQ, AC and WQ)?
please answer question 2,3,4
A critical feature of steel is that a considerable amount of carbon can be dissolved in the austenite, phase, (up to 2.14 w/o at 1147"C), whereas carbon is essentially insoluble in ferrite, Cooling from point d to e, just above the eutectoid but still in the an increased fraction of the +y region, will produce phase and a microstructure similar to that shown: the particles precinitates out in the form af an intermetallic.compound called iron-carbide...
1. By comparing your researched values, obtained through the experiment, with those of the steel manufacturer's: By comparing your researched mechanical properties obtained through this experiment, with those of the steel manufacturer's mechanical properties: (i) Do you find that the material is suitable for the chosen application, i.e. is it "Fit for Purpose"? Compare the critical mechanical properties of Yield Strength, Ultimate tensile Strength, Ductility and Hardness values and state the values in the table below Write a statement about...
1. Draw a schematic stress-strain diagram for steel. Make sure you mark all the important points and regions on it. Provide a one-two sentence explanation for each point and region along the diagram. 2. A cylindrical specimen of a nickel alloy having an elastic modulus of 207 GPa (30 x 10* psi) and an original diameter of 10.2 mm (0.40 In.) will experience only elastic deformation when a tensile load of 8900 N (2000 Ibe) is applied. Compute the maximum length...
I need help to write a nice introduction for experiment 6
please ( no hands write ) typing
Thank you
HEAT TREATMENT OF STEELS EXPERIMENT 6 EXPERIMENT 6 HEAT TREATMENT OF STEELS THEORY The Effect of Cooling Rate One of the most convenient methods for controlling the properties of a given steel, i.e., a steel whose composition is already fixed, consists of austenizing the steel and ten cooling to room temperature at some predetermined rate. A variation of cooling rates...
1. In the H NMR, draw the structure of the molecule directly on
the spectrum and identify each unique proton. Indicate which proton
is responsible for each peak.
2. In the IR spectrum, indicate which functional group is
responsible for each important peak. Attempt to identify at least
five important peaks. In you discussion, indicate which peaks are
most helpful in determining whether or not you converted the
starting material to the desired product.
3. Compare the IR spectrum of...
This is my experiment about Earth magnetic field induction by
tangensgalvonometer. I must additional conclusion for my
experimental values and Bo=1.68x10^-5 T.
Could you compare Bo=1.68x10^-5 and my experimental values.
experiment did same city which is Bo=1.68x10^-5
I need conclusion about this case. thank you.
Results: Bo (1-1 )-7.66x10 Be(l 2-0107 Be (1-3 )-1.72x10 · Be (1-3, 2 )" f,79x16 Bo (Rī9小1.GC-er「 Measurement of the horizontal component of Earth's magnetic field induction by tangensgalvanometer In each point the Earth's magnetic...
Recursion and Trees Application – Building a Word Index Make sure you have read and understood · lesson modules week 10 and 11 · chapters 9 and 10 of our text · module - Lab Homework Requirements before submitting this assignment. Hand in only one program, please. Background: In many applications, the composition of a collection of data items changes over time. Not only are new data items added and existing ones removed, but data items may be duplicated. A list data structure...
Please, i need Unique answer, Use your own words (don't copy and paste). Please, don't use handwriting, Use your keyboard. I need you to redrafting my answer, please.. Q1. How does UPS's approach toward sustainability impact the triple bottom line? Be specific. As a founding member of UPS’s sustainability steering committee have wrestled with the challenge and developed a point of view, one that emphasizes the power of organizational momentum and embraces “enlightened self-interested the companies have a responsibility to contribute...
Discussion questions
1. What is the link between internal marketing and service
quality in the airline industry?
2. What internal marketing programmes could British Airways
put into place to avoid further internal unrest? What potential is
there to extend auch programmes to external partners?
3. What challenges may BA face in implementing an internal
marketing programme to deliver value to its customers?
(1981)ǐn the context ofbank marketing ths theme has bon pururd by other, nashri oriented towards the identification of...