8 ft Probs. 6-40/41 6-42. Draw the influence line for the force in member IJ
pz explain.
6-58. Draw the influence line for the force in member CF, and then determine the maximum force (tension or compression) that can be developed in this member due to a uniform live load of 800 lb/ft which is transmitted to the truss along the bottom cord. AL 10 ft 10ft--.--10 ft 10 ft
Problem #11 Draw the influence line for the force in member IH of the bridge truss. Determine the maximum force (tension or compression) that can be developed in this member due to a 72-k truck having the wheel loads shown. Assume the truck can travel in either direction along the center of the deck, so that half its load is transferred to each of the two side trusses. Also assume the members are pin connected at the gusset plates. 32...
Draw the influence linee for the force in the mebers that
identifies
8 ft 8 ft FIG. P8.54
8 ft 8 ft FIG. P8.54
Consider the truss shown in (Figure 1). Follow the sign convention. Draw the influence line for the force in member CJ. Indicate the values of the influence line at each joint along the bottom cord of the truss and indicate the points where the influence line passes the z-axis. Click on "add vertical line off" to add discontinuity lines. Then click on "add segment" button to add functions between the lines. Note 1 - Draw discontinuity lines at each joint...
12-42. Solve Prob. 12-41 using the cantilever method Each column has the cross-sectional area indicated. 12 ft 6 k 18 ft 20 ft 20 ft 12 in2 8 in2 10 in2 Probs. 12-41/42
2. (30 pts.) 5 m 6 panels at 3 m = 18 m Consider the given truss above and assuming loads acts on the bridge deck along the bottom cord write equations with respect to x and a) Draw the influence line for the force in member CI and IJ by writing necessary equations. (20 pts.) the maximum tension force in member J considering the following uniform dead load wDL-2 kN/m uniform live load wLL-8 kN/m and concentrated live load...
Chapter 6- Influence Lines Draw the influence line for the shear and moment at C for the beam shown below. The support at A is a roller and the support at B is a pin. The beam is subjected to a uniform load of 5 kip/ft over its entire length and a single 12 kip concentrated force. Deternmine the maximum values of Ve and Mc and the position of the applied concentrated force for each condition. Answer: VC: +0.5 at...
(Influence Line Truss) Problem 3. Using STATICS DRAW the INFLUENCE LINES for the FORCE IN MEMBERS FG. SHOW ALL VALUES. LABEL ALL POINTS. MAGNITUDES, AND DISTANCES, Assume the support 'A' is a pin, and 'E is a roller. (6 points) FREE BODY DIAGRAMS & CALCULATIONS H 15 ft A B C D 200 | 2004-2005-2011 IL FFO What is max IL FFG TT T Arial 3 (12pt) > > Path: P Words:0 OLIETION 16 points Save
Determine the support reactions and the force in member CE for
the truss :
8 ft *4fty 300 lb D E F 8 ft A B 3 1000 lb 8 ft * 8 ft
A B C D E F 8' 8' 8' 8' 8' civil engineering
Draw influence lines (show the values and locations for all key points) for the following: Karagi programoginta a) Influence Line for Vertical (upwards) Reaction at F, Fy b) Influence Line for Vertical Reaction at B, BY c) Influence Line for Positive Internal Shear Force just to the right of D, Veight d) Influence Line for Positive Internal Bending Moment at B, M, e) Maximum value of By...