This question is related to real transformers. Kindly show all working.
Assume at full load.
25KVA
This question is related to real transformers. Kindly show all working. Assume at full load. 25KVA...
Al. A 1 kVA single-phase step-down transformer is connected to a 220 V, 50 Hz A.C. source and delivers power to a load. The winding resistance and reactance at secondary side are 0.02 2 and 0.1 12 respectively. The maximum value of core flux is 0.248 mWb and the secondary winding contains 1000 turns. Evaluate a. b. the voltage induced on the secondary side; the turn ratio of primary side to secondary side; the rated current on both sides; and...
Learning Goal: To understand the concepts explaining the operation of transformers.One of the advantages of alternating current (ac) over direct current (dc) is the ease with which voltage levels can be increased or decreased. Such a need is alwayspresent due to the practical requirements of energy distribution. On the one hand, the voltage supplied to the end users must be reasonably low for safety reasons(depending on the country, that voltage may be 110 volts, 220 volts, or some other value...
a) Transformers work by the Principle of Electromagnetic Induction. Briefly explain this to a layman. b) i. [2 marks] [1 mark] State the two (2) types of losses in a transformer and also state where in the [2 marks] State two (2) advantages of an auto-transformer over an ordinary [2 marks] State why DC voltages do not work in transformers. 11. transformer these losses can be found. 111. transformer. c) Explain briefly why electric power is transmitted at very high...
1. If 480 volts is applied to the primary winding of a transformer which has 300 turns in the primary winding and 15 turns in the secondary winding, the secondary voltage will be A. 0.0417 volts. C. 56.8 volts B. 24 volts. D. 9600 volts. 2. A distribution transformer with a grain-orientented steel core is highly efficent because its A. exciting current is sufficiently high. B. flux direction is parallel to the stell-rolling direction C. permeability is increased due to...
Rework problem 3.4 if the load connected to the 240-V secondary winding absorbs 110 kVA under short-term overload conditions at an 0.8 power factor leading and at 230 volts. Reference of problem 3.4 A single phase 100-kVA 2400/240-volt 60 Hz distribution transformer is used as a step down transformer. The load, which is connected to the 240-volt secondary winding, absorbs 60kVA at 0.8 power factor lagging and is at 230 volts. Assuming an ideal transformer, calculate the following: a) primary...
A single-phase 100-kVA, 2400/240-volt, 60-Hz distribution transformer is used as a step-down transformer. The load, which is connected to the 240-volt secondary winding, absorbs 80 kVA at 0.8 power factor lagging and is at 230 volts. Assuming an ideal transformer, calculate the following: a) primary voltage. b) load impedance. c) load impedance referred to the primary. d) the real and reactive power supplied to the primary winding
3.4 A single-phase 100-kVA, 2400/240-volt, 60-Hz distribution transformer is used as a step-down transformer. The load, which is connected to the 240-volt secondary wind- ing, absorbs 80 kVA at 0.8 power factor lagging and is at 230 volts. Assuming an ideal transformer, calculate the following: (a) primary voltage, (b) load impedance, (c) load impedance referred to the primary, and (d) the real and reactive power sup- plied to the primary winding.
Q1 A 1kVA ideal single phase step-up transformer is supplied by a 24 V ac power source and is delivering power to a 10 Ω resistive load connected to the secondary side. If the transformer is operated at full load (1kVA), determine, a) the secondary current IS; (3 marks) b) the secondary voltage VS; (2 marks) c) the primary current IP; (2 marks) d) the turn ratio of primary winding to secondary winding; and (2 marks) e) the number of...
Q-1 A 60Hz, 480V/240V,960V A transformer is supplying a 960W passive load at 240V. The resistances of the primary side and secondary side of the transformer are 1.092 and 0.252 respectively. If the no load losses of the transfomer is given by P-Vã 4800 W where Vn is the input voltage of the transformer in Volt. Answer the following: a) Calculate transformer efficiency b) Do you allow this transformer to be connected to 240V 50Hz distribution system? Explain. c What...
Problem 4 Three ideal single-phase transformers are connected in a delta/wye configuration with the primary side of the three-phase transformer rated at 120 kV and the secondary side rated at 13.8 kV. The rated power of the transformer bank is 20 MVA. One side of the transformer bank is connected to a 120 kV transmission line, and the other side is connected to a three-phase load of 15 MVA at 0.85 lagging power factor. Compute the following: a) The turns...