Develop the part programming for the component shown in Figure 2 using the information in Table...

Question

Question

Develop the part programming for the component shown in Figure 2 using the information in Table 2. Table 2: Machining paramet

Add a comment Improve this question Transcribed image text

Answer 1

Answer #1

(10, 140) (90, 140) 2 150, 1250 3 (32.68 ) - (50,95) 85 11 & 40 O (5975) 85 . (32.68 ) (50,55) 65 OF (6732) 12 65 1 (50,25) 6 N 280. Goo z - 8.0 N 290 Goo X 61.32 8 65; N 300 Gol AZ - 20.5 Floo R5; N 310 N320 Goo z - 8.0 x 67.32 185, R5; Z – 20.5 N 33

Add a comment

Answer 2

Similar Homework Help Questions

Develop a complete CNC program for linear and circular profile for the component shown in Figure...

Develop a complete CNC program for linear and circular profile for the component shown in Figure 1 and Table 1 R10 RZ 07 . 10 18 26 Figure 1: Linear and circular profile of component Table 1: Machining parameters Billet size Ø40 x 83 mm Material Aluminium Operation Profile turning operation Spindle speed 1500 rpm Feed 80 mm/min Tool Left hand roughing
Problem 1 Consider the drilling of Feature 3 (Thru Hole) on the flashlight head (Figure 1)...

Problem 1 Consider the drilling of Feature 3 (Thru Hole) on the flashlight head (Figure 1) Assume the feed of the drilling opcration (i.e., the distance the drill penetrates per unit revolution) is,f= 0.01 inrev. " a) Calculate the material removal rate (in in3/s or mm3/s). b) Use the Taylor Tool Life equation to estimate the tool life (in minutes) for this operation. Use Table 1 to pick appropriate values of C and n (the flashlight material is aluminum and...
Write a CNC part program to machine 15 mm thick aluminum part shown in the figure....

Write a CNC part program to machine 15 mm thick aluminum part shown in the figure. Use an absolute coordinate system. 140 R10 28 40 deep 45 45 155 70 40 $15 20 RIO TOOL CHANHE POINT All dimensions are in mm Three processes are needed to machine the part, 1) Drilling with cutting speed of 1000 rpm and feedrate 70 mm/min. 2) Side milling with cutting speed of 1400 rpm and feedrate 90 mm/min. 3) Slot milling with cutting...

Question 1 2) Manufacturing processes can be classified into 2 (Two) major groups. Briefly describe the...

Question 1 2) Manufacturing processes can be classified into 2 (Two) major groups. Briefly describe the characteristics of each group. Aid your answer with hierarchy. (10 marles) 1) Sand casting is a process for casting metal in sand molds. Explain FIVE (3) sand casting benefits to the industry (marks) Riser, also known as feeder, is an important part in a sand mold. Briefly describe the function of a riser in a sand casting mold Hence, illustrate the possible types and...
If a pump with the characteristic curve shown in the accompanying graph (Figure 2) is used to pump water from the lowe...

If a pump with the characteristic curve shown in the accompanying graph (Figure 2) is used to pump water from the lower to the upper tank (water flows from Tank 2 to Tank 1 in this question) shown in Figure 1. Use information provided in Figure 1 and assume that diameter of pipe AB is 600 mm (DAB 600 ) and diameter of pipe BC is 300 mm DBc 300 mm) a. Find the operation point of this systenm b....
Problems 1-10 Now you have another piece of information - Table 1. It was either obtained...

Problems 1-10 Now you have another piece of information - Table 1. It was either obtained by measuring times to complete each operation, or based on experience with similar operations. For simplicity, setup and cycle times are assumed the same for both 1 and 10.000 parts. To simplify calculations, and without loss of generality, the following is assumed: - The material cost per one part is assumed to be the same, so we neglect it for comparison purposes - Tool...

Need step by step solution please The figure shown is a geared countershaft with an overhanging...

Need step by step solution please The figure shown is a geared countershaft with an overhanging pinion at C. Select an angular- contact ball bearing from Table 11-2 for mounting at O and an 02-series cylindrical rolleor bearing from Table 11-3 for mounting at B. The force on gear A is FA 5 600 lbf, and the shaft is to run at a speed of 420 rovimin. Solution of the statics problem gives force of bearings against the shaft at...
In C++ Programming: Using a single for loop, output the even numbers between 2 and 1004...

In C++ Programming: Using a single for loop, output the even numbers between 2 and 1004 (inclusive) that iterates (loops) exactly 502 times. The outputted numbers be aligned in a table with 10 numbers per row. Each column in the table should be 5 characters wide. Do not nest a loop inside of another loop. Hint: First create and test the code that output the numbers all on one line (the command line will automatically wrap the output to new...

Develop the part programming for the component shown in Figure 2 using the information in Table...

Homework Answers

Add Answer to:
Develop the part programming for the component shown in Figure 2 using the information in Table...

Post as a guest

Earn Coins

Develop a complete CNC program for linear and circular profile for the component shown in Figure...

Problem 1 Consider the drilling of Feature 3 (Thru Hole) on the flashlight head (Figure 1)...

Write a CNC part program to machine 15 mm thick aluminum part shown in the figure....

Question 1 2) Manufacturing processes can be classified into 2 (Two) major groups. Briefly describe the...

If a pump with the characteristic curve shown in the accompanying graph (Figure 2) is used to pump water from the lowe...

Problems 1-10 Now you have another piece of information - Table 1. It was either obtained...

Need step by step solution please The figure shown is a geared countershaft with an overhanging...

In C++ Programming: Using a single for loop, output the even numbers between 2 and 1004...

Develop the part programming for the component shown in Figure 2 using the information in Table...

Homework Answers

Add Answer to: Develop the part programming for the component shown in Figure 2 using the information in Table...

Post as a guest

Earn Coins

Add Answer to:
Develop the part programming for the component shown in Figure 2 using the information in Table...