The bar is connected to the support using a pin having a
diameter of d = 1 in. If the allowable tensile stress for the bar
is (σt)allow = 20ksi, and the allowable bearing stress between the
pin and the bar is (σb)allow =30ksi, determine the minimum
dimension w so that the bar can hold P=100 kips . Assume the hole
in the bar has the same diameter as the pin.
pin.
Homework Answers
![* Ang := d=lin ( allow = zoksi allow = 30 ksi W=? P=100 kips Crushing failure load = {( allow] = 100 = 30 (6) tensile failure](http://img.homeworklib.com/questions/7d97feb0-44b9-11eb-8969-63521645c456.png?x-oss-process=image/resize,w_560)
Add Answer to:
The bar is connected to the support using a pin having a
diameter of d =...
131 The concrete beam is reinforced with three 20-mm- diameter steel rods. Assume that the concrete...
131 The concrete beam is reinforced with three 20-mm- diameter steel rods. Assume that the concrete cannot support tensile stress. If the allowable compressive stress for concrete is (allown2.5 MPa and the allowable tensile stress for steel is (?allow)st-220 MPa, determine the required dimension d so that both the concrete and steel achieve their allowable stress simultaneously. This condition is said to be 'balanced'. Also, compute the corresponding maximum allowable internal moment M that can be applied to the beam....
Rigid bar is supported by a pin-connected axial bar (1) and a pin connection at C...
Rigid bar is supported by a pin-connected axial bar (1) and a pin connection at C as shown in Figure Q1. Member (1) is a 20 mm wide by 9 mm thick rectangular bar made of Steel Alloys (A992). The total strain in bar (1) is measured as 925 ue (925x10°). The pin at C has an ultimate shear strength of ty = 345MPa. Determine: (a) The axial force in member (1). [9 marks] (b) The factor of safety in...
A rigid beam AFBC in Fig.3 is supported by a hinged joint at A and connected to a vertical post B...
A rigid beam AFBC in Fig.3 is supported by a hinged joint at A and connected to a vertical post BD by a hinged connection at B. Rigid beam AFBC and vertical post cross-sectional dimension of 10mmx250mm and 15mmx200mm, respectively. Two concentrated loads Pi and P2 act on the rigid beam at point F and C, respectively. Details at support A and connection B are also shown in the figure. Compute (a) normal stress in vertical post BD (state whether...
D . Select the lightest-weight steel wide-flange overhanging beam from Appendix B that will safely support...
D . Select the lightest-weight steel wide-flange overhanging beam from Appendix B that will safely support the loading. Assume the support at A is a pin and the support Jo now = 12 ks: at B is a roller. The allowable bending stress is allow = (see email data) Zaves IU KS and the allowable shear stress is allow --- 14 ksi. P=11 hip 8t 44 y. Selected beam section is: W X P (see email data for value of...
Bar B of the pin connected system is made of aluminum alloy (E=105 GPa, A=1200 mm^2)...
Bar B of the pin connected system is made of aluminum alloy
(E=105 GPa, A=1200 mm^2) and bar A is made of a hardened carbon
steel (E=210 GPa, A=1200 mm^2). Bar CDE is rigid. When the system
is unloaded, Bars A and B are unstressed.
Determine:
a) The Normal Stress in bars A and B. (5pts)
b) The Shearing Stress in the 20-mm diameter pin E which is in
double shear. (5pts)
c) If the yield stress of the material...
2) The rigid bar CDE is attached to a pin support at E and rests on...
2) The rigid bar CDE is attached to a pin support at E and rests on the 30-mm diameter brass cylinder BD. A 22-mm-diameter steel rod AC passes through a hole in the bar and is secured by a nut which is snugly fitted when the temperature of the entire assembly is 20°C. The temperature of the brass cylinder is then raised to 50°C while the steel rod remains at 20°C. Assuming that no stresses were present before the temperature...
solve incorrect answers please Your answer is partially correct. Try again. A simple pin-connected truss is...
solve incorrect answers please
Your answer is partially correct. Try again. A simple pin-connected truss is loaded and supported as shown in the figure. All members of the truss are aluminum pipes that have an outside diameter of 4.75 in. and a wall thickness of 0.283 in. Determine the normal stress in each truss member. Assume P = 8 kips, Q = 7 kips, a = 7 ft, b = 10 ft, and h - 9 ft. The stresses are...
7. (5 points) A solid circular bar having diameter d is to be replaced by a...
7. (5 points) A solid circular bar having diameter d is to be replaced by a thin-walled triangular tube having the cross-section shown below. Determine the required thickness of the triangular thin-walled tube so that the maximum shear stress in the triangular tube will be equal to the maximum shear stress in the solid bar. The cross section of the tube is an equilateral triangle Both sections are going to be subjected to the same torque. d
2) The rigid bar CDE is attached to a pin support at E and rests on...
2) The rigid bar CDE is attached to a pin support at E and rests on the 30-mm diameter brass cylinder BD. A 22-mm-diameter steel rod AC passes through a hole in the bar and is secured by a nut which is snugly fitted when the temperature of the entire assembly is 20°C. The temperature of the brass cylinder is then raised to 50°C while the steel rod remains at 20°C. Assuming that no stresses were present before the temperature...
1) A circular brass bar AC of diameter 100 mm is rigidly connected to a circular...
1) A circular brass bar AC of diameter 100 mm is rigidly connected to a circular steel bar CB of the same diameter as shown. The composite bar is rigidly held at its two ends A and B. A torque T is applied to the shaft at point C. Knowing that the allowable shear stresses in the brass and steel are 120 MPa and 250 MPa, respectively, determine the allowable torque Tallow. The shear moduli for brass and steel are...
131 The concrete beam is reinforced with three 20-mm- diameter steel rods. Assume that the concrete cannot support tensile stress. If the allowable compressive stress for concrete is (allown2.5 MPa and the allowable tensile stress for steel is (?allow)st-220 MPa, determine the required dimension d so that both the concrete and steel achieve their allowable stress simultaneously. This condition is said to be 'balanced'. Also, compute the corresponding maximum allowable internal moment M that can be applied to the beam....
Rigid bar is supported by a pin-connected axial bar (1) and a pin connection at C as shown in Figure Q1. Member (1) is a 20 mm wide by 9 mm thick rectangular bar made of Steel Alloys (A992). The total strain in bar (1) is measured as 925 ue (925x10°). The pin at C has an ultimate shear strength of ty = 345MPa. Determine: (a) The axial force in member (1). [9 marks] (b) The factor of safety in...
A rigid beam AFBC in Fig.3 is supported by a hinged joint at A and connected to a vertical post BD by a hinged connection at B. Rigid beam AFBC and vertical post cross-sectional dimension of 10mmx250mm and 15mmx200mm, respectively. Two concentrated loads Pi and P2 act on the rigid beam at point F and C, respectively. Details at support A and connection B are also shown in the figure. Compute (a) normal stress in vertical post BD (state whether...
D . Select the lightest-weight steel wide-flange overhanging beam from Appendix B that will safely support the loading. Assume the support at A is a pin and the support Jo now = 12 ks: at B is a roller. The allowable bending stress is allow = (see email data) Zaves IU KS and the allowable shear stress is allow --- 14 ksi. P=11 hip 8t 44 y. Selected beam section is: W X P (see email data for value of...
Bar B of the pin connected system is made of aluminum alloy
(E=105 GPa, A=1200 mm^2) and bar A is made of a hardened carbon
steel (E=210 GPa, A=1200 mm^2). Bar CDE is rigid. When the system
is unloaded, Bars A and B are unstressed.
Determine:
a) The Normal Stress in bars A and B. (5pts)
b) The Shearing Stress in the 20-mm diameter pin E which is in
double shear. (5pts)
c) If the yield stress of the material...
2) The rigid bar CDE is attached to a pin support at E and rests on the 30-mm diameter brass cylinder BD. A 22-mm-diameter steel rod AC passes through a hole in the bar and is secured by a nut which is snugly fitted when the temperature of the entire assembly is 20°C. The temperature of the brass cylinder is then raised to 50°C while the steel rod remains at 20°C. Assuming that no stresses were present before the temperature...
solve incorrect answers please
Your answer is partially correct. Try again. A simple pin-connected truss is loaded and supported as shown in the figure. All members of the truss are aluminum pipes that have an outside diameter of 4.75 in. and a wall thickness of 0.283 in. Determine the normal stress in each truss member. Assume P = 8 kips, Q = 7 kips, a = 7 ft, b = 10 ft, and h - 9 ft. The stresses are...
7. (5 points) A solid circular bar having diameter d is to be replaced by a thin-walled triangular tube having the cross-section shown below. Determine the required thickness of the triangular thin-walled tube so that the maximum shear stress in the triangular tube will be equal to the maximum shear stress in the solid bar. The cross section of the tube is an equilateral triangle Both sections are going to be subjected to the same torque. d
2) The rigid bar CDE is attached to a pin support at E and rests on the 30-mm diameter brass cylinder BD. A 22-mm-diameter steel rod AC passes through a hole in the bar and is secured by a nut which is snugly fitted when the temperature of the entire assembly is 20°C. The temperature of the brass cylinder is then raised to 50°C while the steel rod remains at 20°C. Assuming that no stresses were present before the temperature...
1) A circular brass bar AC of diameter 100 mm is rigidly connected to a circular steel bar CB of the same diameter as shown. The composite bar is rigidly held at its two ends A and B. A torque T is applied to the shaft at point C. Knowing that the allowable shear stresses in the brass and steel are 120 MPa and 250 MPa, respectively, determine the allowable torque Tallow. The shear moduli for brass and steel are...
Most questions answered within 3 hours.
-
You are attempting to calculate a firm’s free cash flow to
equity. You know the following...
asked 38 minutes ago -
the following reaction occurs in a balloon containing
N2O2 gas
N2O4(g)=2NO2(g)
will the volume of the...
asked 1 hour ago -
answer the questions throughout this program
public class Day implements Comparable {
Private Boolean atWork;...
asked 1 hour ago -
This is C++ code for parking fee management program
#include <iostream>
#include <iomanip>
using namespace std;...
asked 1 hour ago -
The free energy change for the following reaction at 25 °C, when
[Sn2+] = 1.17 M...
asked 3 hours ago -
An MNE is this kind of industry when competition in one country
is essentially independent of...
asked 4 hours ago -
. For this set of questions, determine what
proportion of a normal distribution is located betweeneach...
asked 5 hours ago -
A college student is employed as a door-to-door newspaper
salesman. Historical data suggests that the student...
asked 6 hours ago -
MATLAB HW 11 problem using Switch Case and Input commands
Write a script file that calculates...
asked 6 hours ago -
Considering gravitational time dilation, calculate the time that
passes in Earth’s surface while 1 hour passes...
asked 6 hours ago -
Minitab Problem: Take the Lake Hume June rainfall data and find
use the processes outlined in...
asked 7 hours ago -
X Company is trying to decide whether to continue using old
equipment to make Product A...
asked 7 hours ago