I need to solve Minimum outer diameter and value interface of a press fit pulley. It...
I need to solve Minimum outer diameter and value interface of a press fit pulley. It is made of steel and mounted on a shaft.
Shaft E=200000 MPa
Shaft Dia. 30mm
Diameter all intererance delta = .029 mm
Max tangential stress = 116
Homework Answers
Add Answer to:
I need to solve Minimum outer diameter and value interface of a
press fit pulley. It...
QUESTION 1 A shaft where a pulley is to be mounted has a diameter of 82...
QUESTION 1 A shaft where a pulley is to be mounted has a diameter of 82 mm. The pulley transmits a torque of 714 N.m. The shaft is to be made of SAE 4140 alloy steel. The pulley is made from 1095 Carbon steel. The width of the hub of the pulley mounted at this location is 25 mm. The design factor is 5, and pulley rotates at 650 rpm. Sy for Shaft material: 621 MPa Sy for Pulley material:...
02. A shaft where a pulley is to be mounted has a diameter of 58 mm. The pu torque of 500 N.m. wi...
02. A shaft where a pulley is to be mounted has a diameter of 58 mm. The pu torque of 500 N.m. width of the hub of the pulley mounted at this location is 25 mm. Design factor is 25, an ulley rotate at 650 rpm. The shaft is to be made of SAE 4140 alloy steel. The pulley is made from 1095 Carbon seet The ompute the following: [I) Which of shaft, pulley and key has a [2] The...
4) A brass bushing with an inner diameter of 40mm and an outer diameter of 60mm is press fit into a steel tube of outer diameter 100mm. Determine the maximum stress in both materials. Assume the f...
4) A brass bushing with an inner diameter of 40mm and an outer diameter of 60mm is press fit into a steel tube of outer diameter 100mm. Determine the maximum stress in both materials. Assume the following: Eb 110 GPo, E, 200 GPo, v, 0.32, v 0.28, 6 0.07mm. (12 points)
4) A brass bushing with an inner diameter of 40mm and an outer diameter of 60mm is press fit into a steel tube of outer diameter 100mm. Determine the...
A portion of a shaft where a gear is to be mounted has diameter of 50...
A portion of a shaft where a gear is to be mounted has diameter of 50 mm. The gear transmits 335 N-m of torque. The shaft is to be made of SAE 1040 cold-drawn steel. The gear is made from SAE 8650 OQT 1000 steel The width of the hub of the gear mounted at this location is 45 mm. Design the key. The standard key dimension for a 50-mm-diameter shaft would be 14mm '9 mm Q-1 a rectangular. Material...
The following dimensions are given for a standard press and shrink fit of a solid shaft...
The following dimensions are given for a standard press and shrink fit of a solid shaft and a collar: basic size: 40 mm maximum hole diameter: 40.025 mm minimum hole diameter: 40.000 mm maximum shaft diameter: 40.060 mm minimum shaft diameter: 40.044 mm The materials are both carbon steel. Find the maximum and minimum values of: i) the radial interference ii) the interference pressure Use a collar outside diameter of 80 mm.
QUESTION 5 The copper pipe has an outer diameter of 40mm and an inner diameter of...
QUESTION 5 The copper pipe has an outer diameter of 40mm and an inner diameter of 37mm. If it is attached to the wall at point A and three torques are applied as shown, determine the minimum shear stress developed in the pipe. Answers should be given in units of MPa. 30 N m 20 N m 80 N m For the 30mm diameter shaft shown below made of steel (G-200GPa), what is the magnitude of the total angle of...
Pulley Diameter = 800 mm Base Plate Diameter = 1200 mm Shaft Mounted Wheel Axial force...
Pulley Diameter = 800 mm Base Plate Diameter = 1200 mm Shaft Mounted Wheel Axial force F2 along the shaft axis Belt connected to motor with tension force F Figure 1. Side View Belt Bearing A. Bearing B FR = 2 kN --- - - - - - - - - - - > ---- 500 mm 500 mm 500 mm F1 = 500 N 'Fw = 1 kN Figure 2. The design of a fatigue test machine for car...
Q2. Figure Q2 shows a shaft which transmits a power of 48 kW through flat belts. Pulley A is driven by a motor which rotates at 3000 rpm. The diameter of pulley A is 400 mm and that of pulley B is 25...
Q2. Figure Q2 shows a shaft which transmits a power of 48 kW through flat belts. Pulley A is driven by a motor which rotates at 3000 rpm. The diameter of pulley A is 400 mm and that of pulley B is 250 mm. The thickness of the belts is 4 mm and they are made of a material with density of 1100 kg/m3. Assume no sliding between pulleys and belts a) Calculate the speed of the belt and the...
Figure Q1 The jib crane is pinned at A and supports a chain hoist that can travel along the bottom flange of the a) the force in rod BC b) the minimum diameter of rod BC (to the nearest 5 mm)....
Figure Q1 The jib crane is pinned at A and supports a chain hoist that can travel along the bottom flange of the a) the force in rod BC b) the minimum diameter of rod BC (to the nearest 5 mm). c) the minimum diameter of pin B (to the nearest 5 mm). The material properties are listed in Table Q2 and use factor of safety of FS-2 (10 marks) beam boist Figure Q2 Table Q2: Material properties (MPa) Shear...
this is a multi-parts question. I need all A, B, C, D. Only answer if you...
this is a multi-parts
question. I need all A, B, C, D. Only answer if you know them all.
Thx and Will ThumbUp!
Problem 3 (10 points) The stepped shaft made of a material having a shear modulus of elasticity G = 40 GPa is fixed at A and loaded by two torques T = 60 N.m and T2= 80 N.m as shown below. The shaft BC has solid circular cross-section with diameter of 50 mm and the shaft AB...
QUESTION 1 A shaft where a pulley is to be mounted has a diameter of 82 mm. The pulley transmits a torque of 714 N.m. The shaft is to be made of SAE 4140 alloy steel. The pulley is made from 1095 Carbon steel. The width of the hub of the pulley mounted at this location is 25 mm. The design factor is 5, and pulley rotates at 650 rpm. Sy for Shaft material: 621 MPa Sy for Pulley material:...
02. A shaft where a pulley is to be mounted has a diameter of 58 mm. The pu torque of 500 N.m. width of the hub of the pulley mounted at this location is 25 mm. Design factor is 25, an ulley rotate at 650 rpm. The shaft is to be made of SAE 4140 alloy steel. The pulley is made from 1095 Carbon seet The ompute the following: [I) Which of shaft, pulley and key has a [2] The...
4) A brass bushing with an inner diameter of 40mm and an outer diameter of 60mm is press fit into a steel tube of outer diameter 100mm. Determine the maximum stress in both materials. Assume the following: Eb 110 GPo, E, 200 GPo, v, 0.32, v 0.28, 6 0.07mm. (12 points)
4) A brass bushing with an inner diameter of 40mm and an outer diameter of 60mm is press fit into a steel tube of outer diameter 100mm. Determine the...
A portion of a shaft where a gear is to be mounted has diameter of 50 mm. The gear transmits 335 N-m of torque. The shaft is to be made of SAE 1040 cold-drawn steel. The gear is made from SAE 8650 OQT 1000 steel The width of the hub of the gear mounted at this location is 45 mm. Design the key. The standard key dimension for a 50-mm-diameter shaft would be 14mm '9 mm Q-1 a rectangular. Material...
The following dimensions are given for a standard press and shrink fit of a solid shaft and a collar: basic size: 40 mm maximum hole diameter: 40.025 mm minimum hole diameter: 40.000 mm maximum shaft diameter: 40.060 mm minimum shaft diameter: 40.044 mm The materials are both carbon steel. Find the maximum and minimum values of: i) the radial interference ii) the interference pressure Use a collar outside diameter of 80 mm.
QUESTION 5 The copper pipe has an outer diameter of 40mm and an inner diameter of 37mm. If it is attached to the wall at point A and three torques are applied as shown, determine the minimum shear stress developed in the pipe. Answers should be given in units of MPa. 30 N m 20 N m 80 N m For the 30mm diameter shaft shown below made of steel (G-200GPa), what is the magnitude of the total angle of...
Pulley Diameter = 800 mm Base Plate Diameter = 1200 mm Shaft Mounted Wheel Axial force F2 along the shaft axis Belt connected to motor with tension force F Figure 1. Side View Belt Bearing A. Bearing B FR = 2 kN --- - - - - - - - - - - > ---- 500 mm 500 mm 500 mm F1 = 500 N 'Fw = 1 kN Figure 2. The design of a fatigue test machine for car...
Q2. Figure Q2 shows a shaft which transmits a power of 48 kW through flat belts. Pulley A is driven by a motor which rotates at 3000 rpm. The diameter of pulley A is 400 mm and that of pulley B is 250 mm. The thickness of the belts is 4 mm and they are made of a material with density of 1100 kg/m3. Assume no sliding between pulleys and belts a) Calculate the speed of the belt and the...
Figure Q1 The jib crane is pinned at A and supports a chain hoist that can travel along the bottom flange of the a) the force in rod BC b) the minimum diameter of rod BC (to the nearest 5 mm). c) the minimum diameter of pin B (to the nearest 5 mm). The material properties are listed in Table Q2 and use factor of safety of FS-2 (10 marks) beam boist Figure Q2 Table Q2: Material properties (MPa) Shear...
this is a multi-parts
question. I need all A, B, C, D. Only answer if you know them all.
Thx and Will ThumbUp!
Problem 3 (10 points) The stepped shaft made of a material having a shear modulus of elasticity G = 40 GPa is fixed at A and loaded by two torques T = 60 N.m and T2= 80 N.m as shown below. The shaft BC has solid circular cross-section with diameter of 50 mm and the shaft AB...
Most questions answered within 3 hours.
-
find the critical value associated with a right sided hypothesis of
the mean using a sample...
asked 1 hour ago -
Which of the following statements is true with respect to a
simple linear regression model?
a....
asked 2 hours ago -
The energy required to remove an electron from a surface of a
solid element is called...
asked 3 hours ago -
How would you train your employees to avoid risks of using
mobile devices?
asked 4 hours ago -
Assume Kw = 1.01 ✕ 10−14
For pure water, we can calculate [H3O+ ] = [OH...
asked 5 hours ago -
Suppose that on a temperature scale X, water boils at 203.0°X
and freezes at -105.7°X. What...
asked 5 hours ago -
BaS crystallizes in a cubic unit cell with S2- ions on each
corner and each face....
asked 6 hours ago -
A. 0≤P(Oi)≤10≤P(Oi)≤1 for each i
B. P(Oi)≤0P(Oi)≤0
C. P(Oi)=1+P(OCi)P(Oi)=1+P(OiC)
D. P(Oi)≥1P(Oi)≥1
If an experiment consists of...
asked 7 hours ago -
A battery has an emf of 9.20V and an internal resistance of 1.20
ohm. a)What resistance...
asked 7 hours ago -
The area of an elastic circular loop decreases at a constant
rate, dA/dt = −6.60×10−3 m2/s...
asked 8 hours ago -
The denaturation of proteins can be described by the
equilibrium
F⇌U
where F and U represent...
asked 10 hours ago -
Please answer what the maximum and minimum force is, and the
angle on the ion is...
asked 10 hours ago