Problem 3: For the given loading, determine the zero-force members. Justify your answers using appropriate joint...

Question

Question

Problem 3: For the given loading, determine the zero-force members. Justify your answers using appropriate joint free-body di

Answer 1

Answer #1

zero force members are FH, FI, EI, EJ, consider Free Body diagram of Joint EFX -0 Joint H Efy=0 FF H=0 F = FGM Joint F FH is

Answer 2

Similar Homework Help Questions

please solve showing all steps Problem 3. For the given loading, determine the zero-force members in each of the two...

please solve showing all steps Problem 3. For the given loading, determine the zero-force members in each of the two trusses shown C D E C D IH Problem 3. For the given loading, determine the zero-force members in each of the two trusses shown C D E C D IH
Problem 4 EM2 Find zero force members Determine the force in members KJ, CJ, and CD...

Problem 4 EM2 Find zero force members Determine the force in members KJ, CJ, and CD using method of sections and state if the members are in tension or compression. Then use the previous result to find the force in member JE using the method of joints. 30 kN 20 KN 15 kN 15 kN 10 kN 5 kN LKL HG B FI 3 @ 1 m - 3 m 6@ 3 m = 18 m Problem 4 EM2 Find...
Determine the force in members DE, EJ, and JK by the method of sections. Draw all...

Determine the force in members DE, EJ, and JK by the method of sections. Draw all free body diagrams. Below each free body diagram write the equilibrium equations associated with that free body diagram. Failure to format your answers in this fashion will result in a zero. All forces shown are vertical and horizontal 14000 lb 3200 lb E 6700 lb 12-0" 6 bays at 9-0" 54'-0" 5200 lb

Determine the force in members EL and LM of the truss and state if the members...

Determine the force in members EL and LM of the truss and state if the members are in tension or compression. (Draw the free-body diagrams separately. Reaction forces and moments cannot be shown on the original figure.) 3@1m = 3m 41 m = 4 m 500 N 500N
3. For the frame shown in Fig. 3, (a) (7%) determine the support reactions, (b) (6%) draw the fre...

3. For the frame shown in Fig. 3, (a) (7%) determine the support reactions, (b) (6%) draw the free-body diagrams of member AB and member CBD; (c) (12%) replace the loading on the frame by a single resultant force, and specify where its line of action intersects member CD, measured from end C 150 N 500 N 3 m 3m 2 m 400 N -m 0.35 m 0.35 m 3 m 500 N 35° Fig. 3 Fig. 2 Fig. 1...
Problem 05.011- Using a free body diagram, draw V and M diagrams and determine maximum values...

Problem 05.011- Using a free body diagram, draw V and M diagrams and determine maximum values of V and M Consider the given beam and loading where Pa 4 kN 450 N-m 300 mm 300 mm 200 mm References eBook & Resources Problem 05 ofn Using a free bödy diegram. draw V D ond Mdiagiroms ondi geocimine am volues of Section Break

For the joint and loading shown, determine the stress states at points A and B on...

For the joint and loading shown, determine the stress states at points A and B on section-aa, and the principle stresses at point A. The free-body diagram including section-aa is given below for your convenience. Section-aa has a rectangular cross-section area of thickness 12 mm (shown) and width 18 mm. a) Sketch each stress state using a square stress element. b) Determine the principle stresses at point A (no need to sketch the stress element). Problem 1: (25%) For the...
3. Determine zero force members for the following trusses: с Е O D. K (b) Explain...

3. Determine zero force members for the following trusses: с Е O D. K (b) Explain in writing how you are able of observe zero-force members from these diagrams. Also, explain, why some zero-force members in problem (3) were not as obvious to observe.
Using the method of sections, determine the forces in the indicated members of the trusses shown...

Using the method of sections, determine the forces in the indicated members of the trusses shown and state if the member is in tension or compression. In addition, summarize the results on a force summation diagram. Notes: o Answers without a force summation diagram will receive a score of zero. Be sure to draw the free-body diagram(s) of the portion(s) of the section(s) used for analysis. Answers without the diagram(s) will receive a score of zero. Show your work. Answers...

Determine the force in members EL and LM of the truss and state if the members...

Determine the force in members EL and LM of the truss and state if the members are in tension or compression. (Draw the free-body diagrams separately. Reaction forces and moments cannot be shown on the original figure.) 3@1m =3m 1 Н E 4@1m=4m 500N M 500N W OST