The 2 part beam is joined by nails with a shear strength of 450 N. What...

Question

Question

Answer 1

Answer #1

Given dota Shear Strength (T) = 4 500 N/m2 - 150 I so I VITIT VA 150 25 INTř - T- load (v) = 1000 N IN A = 534100 mm 5311009

Answer 2

Similar Homework Help Questions

Problem 4 Nails, each having a total shear strength of 40 pounds, are used in the beam that can b...

Problem 4 Nails, each having a total shear strength of 40 pounds, are used in the beam that can be constructed either as Case I or as Case II. If the nails are spaced at 9 inches, determine the largest vertical shear that can be supported in each case so that the fasteners will not fail s 9 in 0.5 in. 0.5 in 11in 5 in. N s=.9 in Case II Case I n. 0.5 in. in.1 in.1 n 0.5...
The T-shaped beam consists of 2 boards joined by nails, as shown in the figure. a)...

The T-shaped beam consists of 2 boards joined by nails, as shown in the figure. a) Determine the neutral axis and the moment of inertia. b) Son of Demonstrates that the upper and lower static moments (around the neutral axis) equal c) Calculate the maximum shear force to which the T beam is attached סח o o --- 2 12 Fuerza cortante V no
Learning Goal: To calculate the shear stress at the web/flange joint in a beam and use...

Learning Goal: To calculate the shear stress at the web/flange joint in a beam and use that stress to calculate the required nail spacing to make a built- up beam. A built up beam can be constructed by fastening flat plates together. When an l-beam is subjected to a shear load, internal shear stress is developed at every cross section, with longitudinal shear stress balancing transverse shear stress. If the beam is built up using plates, the fasteners used must...

Two boards are nailed together to form a beam. Each board has dimensions of 1.75 inch...

Two boards are nailed together to form a beam. Each board has dimensions of 1.75 inch X 5.75 inch wide. The beam is loaded with an internal shear force of 1000 lb. If the nails are spaced every 4 inches, what is the shear force resisted by each nail?. N A
1. (a) What is the design shear strength of the beam shown if fc' = 21...

1. (a) What is the design shear strength of the beam shown if fc' = 21 MPa; fy = 350 MPa? No shear reinforcing is provided? 4020 425 500 300 (b) What is the design shear strength of the beams shown if fc'= 21 MPa, fy = 350 MPa? Shear reinforcing is provided? 1126 012@ 150mm 675 750 010@150mm 550 800 163 63 1. 450 L 200 - 010@150mm | 300-
The distributed load on the beam shown is 2.5 kN/m. What is the maximum shear stress...

The distributed load on the beam shown is 2.5 kN/m. What is the maximum shear stress in the beam at the interface between the two members (at 150 mm from the bottom). If nails are used to connect the members and the nails have an allowable shear strength of 2 kN, what is the maximum spacing of the nails at the point of maximum shear? 150 mm 25 m 150 mm 0.5 m 25 mm

TOON 150 N 450 N 1000 N/M Question 6 (20 points) Draw the shear and moment...

TOON 150 N 450 N 1000 N/M Question 6 (20 points) Draw the shear and moment diagrams for the beam. The supports at A and B are a thrust bearing and journal bearing, respectively itors 0.5 m A B tim -2m- IM
P5: Q = 6.875 x 10-4 m 3 5. A wooden box beam is fabricated from...

P5: Q = 6.875 x 10-4 m 3 5. A wooden box beam is fabricated from four boards that are fastened together with nails. Each nail can provide a resistance of V 480 N. In service, the box beam will be installed so that bending occurs about the z axis. If the maximum shear force that the box beam will support is V- 4 kN, what is the maximum spacing, s, between nails? 25 mm 250 mm 25 mm 40...
3. The beam is made from four boards nailed together as shown. If the nails can...

3. The beam is made from four boards nailed together as shown. If the nails can each support a shear force of 100 lb., determine their required spacing s' and s if the beam is subjected to a shear of V-700Lb 1 in. 1 in. 2 in. 910 in. 1 in. 10 in. в, 1.5 in

Review An engineered wood beam (Figure 1) will replace a portion of a structural wall as...

Review An engineered wood beam (Figure 1) will replace a portion of a structural wall as part of a house renovation. The beam can be modeled as a simply supported beam with a span L = 18 ft and an uniform distributed load w = 810 lb/ft . The beam is to be constructed as an I-beam with nails securing the flanges to the web. The flanges are 6 in wide and 1 in thick. The web has depth 18...