Question

Consider the circuits below with ideal diodes, R = 2 ks, C = 1 uF, and Vbi = VB2 = 3 V. (a) Calculate the current through D,

0 0
Add a comment Improve this question Transcribed image text
Answer #1

RO R=2; C = 1 F ; VBI = VB. rivo, = VB2=30 (1) Vin 5V 20 ; Vin 3V Vin:50 (I Voull - diode is on; C: diode is ideal) anh M TVin: 10 sin (ali x10x1) R out Vin <3V ; diode is off; - Voul Vin Vin 73V ; diode is on; Vout - 3v ( sdeal diode) Vir - - V >Vin = 10 Sin (or i t ) ne vout Vin + i 31 of vin = Vp=lov (Diode-on] [capacitoon charging phase] 1 - Ve(vp-3) VE) = 10-3-1V *10V - -10 - - - - - - - - - - - - - .. function. clampor

Add a comment
Know the answer?
Add Answer to:
Consider the circuits below with ideal diodes, R = 2 ks, C = 1 uF, and...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • 24) For the three circuits (a), (b) and (c) shown below, the waveform of input voltage...

    24) For the three circuits (a), (b) and (c) shown below, the waveform of input voltage vy is given as shown below. For each circuit, sketch the waveform of output voltage vo for the given input voltage . Label the most positive and most negative output levels. Assume all diodes are ideal (vp- 0) and CR>> T. (10 points) +10 V-- -10 V TI ms (3 points) (b) o- (3 points) 3V (4 points) DH

  • QUESTION (2) The diodes are ideal except with an on-voltage of 0.7V. The input voltage source...

    QUESTION (2) The diodes are ideal except with an on-voltage of 0.7V. The input voltage source vIN is a 100Hz, 50% duty cycle square-wave with voltage levels of OV and +10V. The load resistance, R = 1002 DL D a) If the ripple voltage, V 0.5V, sketch the output waveform for several input cycles. What is the average DC output voltage vo + D. C R (6 points) Vo VIN b) What would be the minimum value of C (in...

  • Fig. 3 as follows is an IC layout of a CMOS implementation of a two-input digital...

    Fig. 3 as follows is an IC layout of a CMOS implementation of a two-input digital logic gate. The truth table of the logic gate is also given. Voo Vini Vina Vout OVOV 3 V OV 3V 3 V Vint Vina out 3V10 V 3V 3V 3V OV GND Fig. 3 (a). How many MOSFETs are there in the IC layout shown above? (2 marks) (b). The given layout is drawn according to the lambda () design rules. If a...

  • Problem #2: A clipper circuit based on diodes are simple way to modify waveform in mechatronics....

    Problem #2: A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the V..t) 10 k? 10 k? Vin(t ms -8V Page | 1

  • Answer all the questions, please. 1) 2) In the circuit below, if VB1 = 1.3V and...

    Answer all the questions, please. 1) 2) In the circuit below, if VB1 = 1.3V and VB2 = 2.3V, what is the maximum possible value of the output voltage v? Assume a drop of 0.7V across the diodes when forward-biased. Enter your answer in volts. DÝ D2 VBI = Von The circuit below shows a linear regulator. Assume the unregulated input voltage is Vin = 18 V, the Zener specs are (Vz = 5.1 V. Iz = 50 mA), R1...

  • 1. Consider the single-phase VSI inverter shown below dc VR(t) iz(t) a) If your input voltage Vdc...

    1. Consider the single-phase VSI inverter shown below dc VR(t) iz(t) a) If your input voltage Vdc - 100V2 V and switching frequency is 60 Hz with zero delay angle. Then, sketch the square wave output. Mark the peak values [10 marks] b) Sketch the fundamental output on the top of the above waveform. Mark the peak value По marksl c) The above A VSI is used to create a square wave output with 100v2 V at 60 Hz. This...

  • Please note that D4 is the one that was destroyed not D1. Please I posted this but they answer it...

    Please note that D4 is the one that was destroyed not D1. Please I posted this but they answer it differently QUESTION (2) Due to an abnormal operating condition, Diode D4 in this full-wave rectifier circuit was suddenly destroyed, and stopped Vconducting in both forward and reverse directions (i.e. open circuit) C- R Assume that all other diodes are ideal with zero forward voltage drop and that the time constant RC- 5 ms. stt) 10V For a 1 kHz triangular...

  • 2. Diode circuits and output waveforms. (a) Sketch the output waveforms expected when a 100Hz, 6V...

    2. Diode circuits and output waveforms. (a) Sketch the output waveforms expected when a 100Hz, 6Vp sine wave is applied to each of the circuits shown. Label important voltage levels and time values. Your plots should be large enough, at least 4 to 6 inches on a side, and semi-quantitative to represent accurately the output waveform. Note: the input signal is ap- plied to the left side of the circuit and the output taken from the two terminals on the...

  • QUESTION 5 (15 points) a. You have a power supply which is a full-wave rectifier with a capacitor filter. It operates f...

    QUESTION 5 (15 points) a. You have a power supply which is a full-wave rectifier with a capacitor filter. It operates from the mains and provides an output of Voc-20 V with 20% ripple, when the load current is 2 A Calculate the maximum and minimum values of the output waveform of this power supply. b. Now you will design a series voltage regulator between the power supply described in part (a) and an electronic device operating at 12 VDC...

  • Challenge Problem... The circuit to the left is constructed with a 1k2 resistor and a 1 mF capacitor. The input wavefor...

    Challenge Problem... The circuit to the left is constructed with a 1k2 resistor and a 1 mF capacitor. The input waveform is shown below. i(t) in 2 V, (t) o2 13 A) Sketch a graph of the output voltage for this graph, starting att 0 and ending it once the RESISTOR has returned to an apparent steady state. Be sure to label important points and values. B) What is the value of output voltage at t 11 seconds? 12 seconds?...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT