2. 1000 points Liqudglycern is twing thro gh a25mmdar eter and 16- Hong bbe. The 1...
In the final stages of production, a pharmaceutical is sterilized by heating it from 25 to 75°C as it moves at 0.22 m/s through a straight thin-walled stainless steel tube of 12.7-mm diameter. A uniform heat flux is maintained by an electric resistance heater wrapped around the outer surface of the tube. If the tube is 10 m long, what is the required heat flux? If fluid enters the tube with a fully developed velocity profile and a uniform temperature...
Reviewer 4. Water flows steadily at 1.8kg/s through a 30mm diameter tube that is Score 5m long. The water enters at 20 C, and the tube temperature is maintained at 95 C by steam condensing on the exterior surface. Determine the outlet temperature of the water and the rate of heat transfer to the water. (20 scores) Properties: water (310K): c 4178J/kg-K, 695x106N*s/m2, k=0.628W/m-K, Pr 4.62. water (368K): -296x 10NS/m2 Reviewer 4. Water flows steadily at 1.8kg/s through a 30mm...
Problem 2: Heat exchanger (25 points) Cold water (op 4179 J/kg K) enters the tubes of a heat exchanger at 20 °C at a rate of 3 kgs. while hot oil (cp 2200 J/kg.K) enters the shell at 130 C at the same mass flow rate and leaves at 60°C The heat exchanger consistsoftwo shells and 20 tubes, each executing four passes (two passes per shell). If the W/m2-K, assume the tube wall is very thin with convective heat transfer...
Consider a chemical reactor that has a constant heat release. In this reactor, there are 1-m long cylindrical pipes (L) have inner diameter of 25 mm (D) and Helium gas enters each of the pipe at 400K (Ti) and exits at 800K (Te) that is used to cool the reactor at atmospheric pressure and has mass flow rate as 0.02 kg/s. Determine; (Helium properties at Tf; ρ=0.08 kg/m3; Cp=5200 J/kg.K; µ= 32*10-6 kg.m/s ; k=0.23 W/m.K; Pr= 0.72) the surface...
2. (10 points) A pharmaceutical fluid is sterilized by heating it from 25 to 75 °C as it moves at 0.2 m/s through a straight thin-walled stainless steel tube of 12.7-mm diameter that is 10 m long. A uniform heat flux is maintained by an electric resistance heater wrapped around the outer surface of the straight tube. The pharmaceutical fluid properties may be approximated as: p = 1000 kg/mº, cp = 4 kJ/kg-K, u = 2.102 kg/s-m, k = 1...
Liquid water flows in an ASTM B75 copper tube at a mass flow rate of 3.6 g/s. The water enters the tube at 40°C, and the tube surface is subjected to a constant heat flux at a rate of 1.8 kW. The tube is circular with an inner diameter of 25 mm and a length of 3 m. The maximum use temperature for ASTM B75 copper tube is 204°C. Would the surface temperature of the tube exceed the maximum use...
4. (25 pts) Water is flowing inside a thin wall, smooth pipe of diameter 0.05 m at a mass flowrate of 0.3 kg/s. The water enters the pipe at a mean temperature Tm,i= 80 °C and exits at Tm,o= 80 °C while the pipe surface temperature is maintained at Ts= 20 °C along its entire length. a. Is the flow turbulent or laminar? b. Calculate the average convection heat transfer coefficient inside the tube. c. Calculate the length of the...
A concentric tube heat exchanger for cooling lubricating oil
consists of a thin-walled inner tube of 25 mm diameter carrying
water and an outer tube of 45 mm diameter carrying the oil. The
exchanger operates in countercurrent flow with an overall heat
transfer coefficient of 55 W/m2 K and the tabulated average
properties given below. Mass flow rates of oil and water are both
0.1 kg/s, oil enters the exchanger at 100°C, and water enters the
exchanger at 30°C. (a)...
Problem 3 has properties of engine oil: d = 248.7x104 (N.s)/m², p=845.7 kg/m",k=0.1379 W/m-K, Pr= 390.2, p=2163 J/kg-K. Write them down to your scratch paper before starting self-test. A 10-mm diameter tube has a maintained surface temperature of 180°C. Engine oil enters the tube at 70°C at a flow rate of 1.3 kg/s and exits at 105°C. Find the length, in m, of the tube and well as the corresponding heat transfer rate, in W. Assume fully developed flow and...
PROBLEM #3 (30 points) A shell-and (N 20) is used to heat vegetable oil on the shell side using hot water on tethat side. is Lp- 3.0 m). Each copper tube has dimensions of 15.56-mm ID and 19.05-mm OD and thermal conductivity of copper is 390 W/m-K. Water at a total flow rate of 3.33 kg/s enters the tubes of the heat exchanger at 360 K and leaves at 300 K The inlet and outlet temperatures of oil are 290...