Homework Answers
Please rate...if any
doubt comment please!
Add Answer to:
n 1 A cylindrical pressure vessel is fabricated from steel plating that has a diameter of...
A closed cylindrical pressure vessel has an internal diameter of 1.0m and made of steel of...
A closed cylindrical pressure vessel has an internal diameter of
1.0m and made of steel of thickness 0.01m. Principal stresses at a
point
A closed cvlindrical pressure vessel has an internal diameter of 1.0 m and is made of steel plate of thickness 0.010m. The internal pressure is 5 MPa. The vield strength of the steel under uniaxial tension is 200 MPa. Determine the principal stresses at a point on the internal surface of the vessel. Will the wall of...
A cylindrical pressure vessel of 250 mm mean diameter and 6 mm wall thickness is fabricated...
A cylindrical pressure vessel of 250 mm mean diameter and 6 mm
wall thickness is fabricated from a 1.2 m length of spirally welded
pipe AB as shown. Tank gauge pressure is 4 MPa and centric axial
forces P and P1 of 240 kN act through rigid end plates. Determine:
(a) Net longitudinal and hoop stresses. (b) Normal stress acting
perpendicular to weld and shear stress parallel to weld (show
sketch of Mohr’s circle). (c) Determine the Factor of Safety...
Q2. Figure Q2 shows a cylindrical pressure vessel made by welding semi-spherical caps to a cylindrical...
Q2. Figure Q2 shows a cylindrical pressure vessel made by welding semi-spherical caps to a cylindrical body. The cylindrical part has inner diameter Di = 1.8 m and the wall thickness, t, is uniform and equal to 6 mm. The internal pressure is p = 1.5 MPa. d) What is the value of a force F, applied in the direction of the axis of the cylinder which would make the direct stress in longitudinal direction, in the cylinder wall, one...
Question 3 A typical load case for a cylindrical pressure vessel which is on the back...
Question 3 A typical load case for a cylindrical pressure vessel which is on the back of a truck is estimated to include the d 1.5 m t10 mm internal pressure of p = 2 MPa torsion of and a p = 2 MPa T= 1000 kNm. The internal diameter of the pressure vessel is 1.5 m and the wall thickness is 10 mm. The vessel is made of steel with a yield stress of Sy = 400 MPa Based...
A compressed air vessel has an inside diameter of 2 m and a plate thickness of 12,5 mm. If the tensile stress induc...
A compressed air vessel has an inside diameter of 2 m and a plate thickness of 12,5 mm. If the tensile stress induced in the plating is to be limited to 100 MPa, calculate for both the longitudinal and circumferential seams the pressure necessary to induce this stress. Take the longitudinal and circumferential joint efficiencies as 80% and 50% respectively. What would the actual allowable 2 pressure be? [l MPa)
A compressed air vessel has an inside diameter of 2...
Q3 (30) A cylindrical pressure vessel is constructed from a long, narrow steel plate by wrapping...
Q3 (30) A cylindrical pressure vessel is constructed from a long, narrow steel plate by wrapping the plate around a mandrel and then welding along the edges of the plate to make a helical joint α 55° with the longitudinal axis. The vessel has inner radius r-1.8 m and wall thickness t 20 mm. The material is steel with modulus E: 200 GPa and Poisson's ratio0.30. The internal pressure p is 800 kPa Helical weld . The helical weld makes...
A compressed air vessel has an inside diameter of 2 m and a plate thickness of...
A compressed air vessel has an inside diameter of 2 m and a plate thickness of 12,5 mm. If the tensile stress induced in the plating is to be limited to 100 MPa, calculate for both the longitudinal and circumferential seams the pressure necessary to induce this stress. Take the longitudinal and circumferential joint efficiencies as 80% and 50% respectively. What would the actual allowable 2 pressure be? [l MPa)
The cylindrical pressure vessel has an inner radius of 1.25 m and a wall thickness of...
The cylindrical pressure vessel has an inner radius of 1.25 m
and a wall thickness of 25 mm . It is made from steel plates that
are welded along the 45∘ seam. The vessel is subjected to an
internal pressure of 7 MPa . (Figure 1)
Part A
Determine the normal stress component along this seam.
Express your answer to three significant figures and include the
appropriate units.
Part B
Determine the shear stress component along this seam.
Express your...
We have a filament-wound pressure vessel fabricated from E-glass/epoxy with the strength properties as listed below....
We have a filament-wound pressure vessel fabricated from E-glass/epoxy with the strength properties as listed below. The diameter d 1 m, and wall thickness 20 mm. The vessel is subjected to an internal pressure, p. The fiber orientation囝囝= 53 degree. Determine the maximum internal pressure p, which would cause failure of the vessel according to (a) the maximum stress criterion and (b) the Tsai-Hill criterion (no need to solve "b" - we will learn Tsai-Hill failure criterion from Chapter #...
0.10m Assuming the surface of an Aluminum (E-70 Gpa and v = 0.30) cylindrical pressure vessel...
0.10m Assuming the surface of an Aluminum (E-70 Gpa and v = 0.30) cylindrical pressure vessel is in a state of plain stress, with an internal gas pressure of P - 8 MPa. Determine the strain in the z-direction (z) if the "hoop" stress and "longitudinal" stress of the vessel are defined as: OLA P-r Pr and ơL--2t if the radius of the pressure vessel is r-0.04 m and the wall thickness is t 0.004 mm. Note: the image to...
A closed cylindrical pressure vessel has an internal diameter of
1.0m and made of steel of thickness 0.01m. Principal stresses at a
point
A closed cvlindrical pressure vessel has an internal diameter of 1.0 m and is made of steel plate of thickness 0.010m. The internal pressure is 5 MPa. The vield strength of the steel under uniaxial tension is 200 MPa. Determine the principal stresses at a point on the internal surface of the vessel. Will the wall of...
A cylindrical pressure vessel of 250 mm mean diameter and 6 mm
wall thickness is fabricated from a 1.2 m length of spirally welded
pipe AB as shown. Tank gauge pressure is 4 MPa and centric axial
forces P and P1 of 240 kN act through rigid end plates. Determine:
(a) Net longitudinal and hoop stresses. (b) Normal stress acting
perpendicular to weld and shear stress parallel to weld (show
sketch of Mohr’s circle). (c) Determine the Factor of Safety...
Q2. Figure Q2 shows a cylindrical pressure vessel made by welding semi-spherical caps to a cylindrical body. The cylindrical part has inner diameter Di = 1.8 m and the wall thickness, t, is uniform and equal to 6 mm. The internal pressure is p = 1.5 MPa. d) What is the value of a force F, applied in the direction of the axis of the cylinder which would make the direct stress in longitudinal direction, in the cylinder wall, one...
Question 3 A typical load case for a cylindrical pressure vessel which is on the back of a truck is estimated to include the d 1.5 m t10 mm internal pressure of p = 2 MPa torsion of and a p = 2 MPa T= 1000 kNm. The internal diameter of the pressure vessel is 1.5 m and the wall thickness is 10 mm. The vessel is made of steel with a yield stress of Sy = 400 MPa Based...
A compressed air vessel has an inside diameter of 2 m and a plate thickness of 12,5 mm. If the tensile stress induced in the plating is to be limited to 100 MPa, calculate for both the longitudinal and circumferential seams the pressure necessary to induce this stress. Take the longitudinal and circumferential joint efficiencies as 80% and 50% respectively. What would the actual allowable 2 pressure be? [l MPa)
A compressed air vessel has an inside diameter of 2...
Q3 (30) A cylindrical pressure vessel is constructed from a long, narrow steel plate by wrapping the plate around a mandrel and then welding along the edges of the plate to make a helical joint α 55° with the longitudinal axis. The vessel has inner radius r-1.8 m and wall thickness t 20 mm. The material is steel with modulus E: 200 GPa and Poisson's ratio0.30. The internal pressure p is 800 kPa Helical weld . The helical weld makes...
A compressed air vessel has an inside diameter of 2 m and a plate thickness of 12,5 mm. If the tensile stress induced in the plating is to be limited to 100 MPa, calculate for both the longitudinal and circumferential seams the pressure necessary to induce this stress. Take the longitudinal and circumferential joint efficiencies as 80% and 50% respectively. What would the actual allowable 2 pressure be? [l MPa)
The cylindrical pressure vessel has an inner radius of 1.25 m
and a wall thickness of 25 mm . It is made from steel plates that
are welded along the 45∘ seam. The vessel is subjected to an
internal pressure of 7 MPa . (Figure 1)
Part A
Determine the normal stress component along this seam.
Express your answer to three significant figures and include the
appropriate units.
Part B
Determine the shear stress component along this seam.
Express your...
We have a filament-wound pressure vessel fabricated from E-glass/epoxy with the strength properties as listed below. The diameter d 1 m, and wall thickness 20 mm. The vessel is subjected to an internal pressure, p. The fiber orientation囝囝= 53 degree. Determine the maximum internal pressure p, which would cause failure of the vessel according to (a) the maximum stress criterion and (b) the Tsai-Hill criterion (no need to solve "b" - we will learn Tsai-Hill failure criterion from Chapter #...
0.10m Assuming the surface of an Aluminum (E-70 Gpa and v = 0.30) cylindrical pressure vessel is in a state of plain stress, with an internal gas pressure of P - 8 MPa. Determine the strain in the z-direction (z) if the "hoop" stress and "longitudinal" stress of the vessel are defined as: OLA P-r Pr and ơL--2t if the radius of the pressure vessel is r-0.04 m and the wall thickness is t 0.004 mm. Note: the image to...
Most questions answered within 3 hours.
-
1) If Nominal GDP is $16,000 billion and the GDP deflator is 50,
then Real GDP...
asked 20 seconds ago -
D. A student completed 20 courses in the School of Arts and
Sciences. Her grades in...
asked 1 hour ago -
teo
pucks moving on a frictionless air table are about to collide. the
1.5 kg puck...
asked 1 hour ago -
Problem #1
The area between Z = 0 and Z = 2.50
The area between Z...
asked 3 hours ago -
1. What is the meaning of the term communication style?
2. What are the benefits to...
asked 2 hours ago -
9.) You are buying a car that cost $26,500. You make payments of
$412 each month...
asked 3 hours ago -
. Suppose a discrete random variable has probability
distribution
P(x) = .2 if x = 0...
asked 4 hours ago -
Under the influence of its drive force, a snowmobile is moving
at a constant velocity along...
asked 4 hours ago -
Why do organizations decline? What steps can top
management take to halt, decline, and restore organizational...
asked 4 hours ago -
What mechanisms Drive speciation??
(I.e. what was Dawins theory on the orgin of species, and how...
asked 6 hours ago -
The manager at a car assembly plant believes that the mean
assembly time for a car...
asked 7 hours ago -
Which of the following is true of electron capture?
A) It decreases the nuclide's mass number...
asked 8 hours ago