A cylindrical pressure vessel of 250 mm mean diameter and 6 mm wall thickness is fabricated...
A cylindrical pressure vessel of 250 mm mean diameter and 6 mm
wall thickness is fabricated from a 1.2 m length of spirally welded
pipe AB as shown. Tank gauge pressure is 4 MPa and centric axial
forces P and P1 of 240 kN act through rigid end plates. Determine:
(a) Net longitudinal and hoop stresses. (b) Normal stress acting
perpendicular to weld and shear stress parallel to weld (show
sketch of Mohr’s circle). (c) Determine the Factor of Safety which
exists according to the distortion energy theorem, if the material
is steel with a yield stress 
Y = 300 MPa.
Homework Answers
Add Answer to:
A cylindrical pressure vessel of 250 mm mean diameter and 6 mm
wall thickness is fabricated...
A pressure vessel of 12” outer diameter and 0.2” wall thickness is fabricated by welding plate...
A pressure vessel of 12” outer diameter and 0.2” wall thickness is fabricated by welding plate in spiral into a cylinder that is 4 feet long. The gage pressure inside the vessel is 800 psi and 15 kip axial compression forces are applied to the rigid end caps. Determine the a) the principle stresses in the walls of the vessel, b) the maximum shear stress in the wall of the vessel (in or out of plane), c) the stress normal...
P14.011 The pressure tank is fabricated from spirally wrapped metal plates that are welded at the...
P14.011 The pressure tank is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 780 mm and a wall thickness of 10.3 mm. For a gage pressure of 1.23 MPa, determine (a) the normal stress perpendicular to the weld (use positive for tension, negative for compression) and (b) the shear stress (absolute value) parallel to the weld. Assume B 56 Answers: (e) Normal stress -MPa (b)...
A cylindrical pressure vessel is constructed by welding steel plates together. The pressure vessel supports an...
A cylindrical pressure vessel is constructed by welding steel
plates together. The pressure vessel supports an internal pressure
of 240 (psi). In addition the pressure vessel supports an axial
load of 270000 (lbs.). The inner radius of the pressure vessel is
48 (inches) with a wall thickness of 0.3125 (inches). The plates
are welded at 72 degrees from the horizontal. Determine:
a) the stresses perpendicular and parallel to the weld. Show the
stresses on a properly oriented differential element.
The...
A strain gauge affixed to the outside of a cylindrical pressure vessel at an angle of...
A strain gauge affixed to the outside of a cylindrical
pressure vessel at an angle of θ = 35° reads ε = 400 μm/m. The
outside diameter of the vessel is 500mm and the wall thickness is 5
mm. If the veseel is constructed of A36 steel, determine the
following:
a) The hoop and longitudinal stresses in the tank.
Hints: To solve you will need to consider the equations for
strain transform and generalized Hooke’s Law. The hoop and
longitudinal...
The pressure tank in the figure is fabricated from spirally wrapped metal plates that are welded ...
The pressure tank in the figure is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown where Assume 53. The tank has an inside diameter of 65 in. and a wall thickness of 0.29 in. Determine the largest allowable gage pressure if the allowable normal stress perpendicular to the weld is 11.9 ksi and the allowable shear stress parallel to the weld is 8.9 ksi es
The pressure tank in the figure is...
12 Section 4. Problem 12 (25 pts.) A cylindrical pressure vessel is constructed by welding steel...
12 Section 4. Problem 12 (25 pts.) A cylindrical pressure vessel is constructed by welding steel plates together. The pressure vessel supports an internal pressure of 250 (psi). In addition the pressure vessel supports an axial load of 230000 (lbs.). The inner radius of the pressure vessel is 56 (inches) with a wall thickness of 0.4375 (inches). The plates are welded at 57 degrees from the horizontal. Determine: a) the stresses perpendicular and parallel to the weld. Show the stresses...
- 3. A propane storage tank is constructed by welding two hemispherical end caps onto a...
- 3. A propane storage tank is constructed by welding two hemispherical end caps onto a cylindrical main body. The cylindrical body is manufactured from a helical welded pipe which has an outside diameter of 750 mm and a wall thickness of 6 mm. The tank is designed to hold gas at an internal gauge pressure of 6 MPa. a) Draw the Mohr’s circle and determine the normal and shear stresses on the weld in the cylindrical main body portion...
n 1 A cylindrical pressure vessel is fabricated from steel plating that has a diameter of...
n 1 A cylindrical pressure vessel is fabricated from steel plating that has a diameter of 1.5 m, and is subjected to an internal pressure of 2.5 MPa. Calculate its safe wall thickness if the longitudinal stress is limited to 70 MPa. out of
The cylindrical pressure vessel has an inner radius of 1.25 m and a wall thickness of...
The cylindrical pressure vessel has an inner radius of 1.25 m
and a wall thickness of 25 mm . It is made from steel plates that
are welded along the 45∘ seam. The vessel is subjected to an
internal pressure of 7 MPa . (Figure 1)
Part A
Determine the normal stress component along this seam.
Express your answer to three significant figures and include the
appropriate units.
Part B
Determine the shear stress component along this seam.
Express your...
em 35? ? A cylindrical pressure vessel is constructed from a long, narrow steel plate by...
em 35? ? A cylindrical pressure vessel is constructed from a long, narrow steel plate by wrapping the plate around a mandrel and then welding along the edges of the plate to make a helical joint. The helical weld makes an angle ? 350 with the axial direction. The vessel has inner radius r = 1.8 m and wall thickness 20 mm. The material is steel with E 200 GPa and Poisson ratio 0.3. The internal pressure p = 800...
A pressure vessel of 12” outer diameter and 0.2” wall thickness is fabricated by welding plate in spiral into a cylinder that is 4 feet long. The gage pressure inside the vessel is 800 psi and 15 kip axial compression forces are applied to the rigid end caps. Determine the a) the principle stresses in the walls of the vessel, b) the maximum shear stress in the wall of the vessel (in or out of plane), c) the stress normal...
P14.011 The pressure tank is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 780 mm and a wall thickness of 10.3 mm. For a gage pressure of 1.23 MPa, determine (a) the normal stress perpendicular to the weld (use positive for tension, negative for compression) and (b) the shear stress (absolute value) parallel to the weld. Assume B 56 Answers: (e) Normal stress -MPa (b)...
A cylindrical pressure vessel is constructed by welding steel
plates together. The pressure vessel supports an internal pressure
of 240 (psi). In addition the pressure vessel supports an axial
load of 270000 (lbs.). The inner radius of the pressure vessel is
48 (inches) with a wall thickness of 0.3125 (inches). The plates
are welded at 72 degrees from the horizontal. Determine:
a) the stresses perpendicular and parallel to the weld. Show the
stresses on a properly oriented differential element.
The...
A strain gauge affixed to the outside of a cylindrical
pressure vessel at an angle of θ = 35° reads ε = 400 μm/m. The
outside diameter of the vessel is 500mm and the wall thickness is 5
mm. If the veseel is constructed of A36 steel, determine the
following:
a) The hoop and longitudinal stresses in the tank.
Hints: To solve you will need to consider the equations for
strain transform and generalized Hooke’s Law. The hoop and
longitudinal...
The pressure tank in the figure is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown where Assume 53. The tank has an inside diameter of 65 in. and a wall thickness of 0.29 in. Determine the largest allowable gage pressure if the allowable normal stress perpendicular to the weld is 11.9 ksi and the allowable shear stress parallel to the weld is 8.9 ksi es
The pressure tank in the figure is...
12 Section 4. Problem 12 (25 pts.) A cylindrical pressure vessel is constructed by welding steel plates together. The pressure vessel supports an internal pressure of 250 (psi). In addition the pressure vessel supports an axial load of 230000 (lbs.). The inner radius of the pressure vessel is 56 (inches) with a wall thickness of 0.4375 (inches). The plates are welded at 57 degrees from the horizontal. Determine: a) the stresses perpendicular and parallel to the weld. Show the stresses...
- 3. A propane storage tank is constructed by welding two hemispherical end caps onto a cylindrical main body. The cylindrical body is manufactured from a helical welded pipe which has an outside diameter of 750 mm and a wall thickness of 6 mm. The tank is designed to hold gas at an internal gauge pressure of 6 MPa. a) Draw the Mohr’s circle and determine the normal and shear stresses on the weld in the cylindrical main body portion...
n 1 A cylindrical pressure vessel is fabricated from steel plating that has a diameter of 1.5 m, and is subjected to an internal pressure of 2.5 MPa. Calculate its safe wall thickness if the longitudinal stress is limited to 70 MPa. out of
The cylindrical pressure vessel has an inner radius of 1.25 m
and a wall thickness of 25 mm . It is made from steel plates that
are welded along the 45∘ seam. The vessel is subjected to an
internal pressure of 7 MPa . (Figure 1)
Part A
Determine the normal stress component along this seam.
Express your answer to three significant figures and include the
appropriate units.
Part B
Determine the shear stress component along this seam.
Express your...
em 35? ? A cylindrical pressure vessel is constructed from a long, narrow steel plate by wrapping the plate around a mandrel and then welding along the edges of the plate to make a helical joint. The helical weld makes an angle ? 350 with the axial direction. The vessel has inner radius r = 1.8 m and wall thickness 20 mm. The material is steel with E 200 GPa and Poisson ratio 0.3. The internal pressure p = 800...
Most questions answered within 3 hours.
-
Find the critical value(s) and rejection region(s) for a
two-tailed chi-square test with a sample size...
asked 40 seconds ago -
One of your experts gave me an answer of $7.36 but there are
many different answers...
asked 6 minutes ago -
Petrus Framing's cost formula for its supplies cost is $1,790
per month plus $10 per frame....
asked 19 minutes ago -
Introduction
Information design is a field that studies the way information
should be displayed, which is...
asked 16 minutes ago -
1.The main product of the reaction between p-cresol and Br2 /
FeBr3 is:
3-Bromo-4-methyl phenol
2-Bromo-4-methyl...
asked 20 minutes ago -
At present, concentration
of 92235U in naturally
occurring uranium deposits is approximately 0.74 %. What will the...
asked 23 minutes ago -
Question 1:
For the following reaction, 8.72 grams of nitrogen gas are
allowed to react with...
asked 25 minutes ago -
Discuss the benefits and detriments of hard water, and your
opinion on using water softeners.
asked 1 hour ago -
For a Friedel-Crafts alkylation reaction between
1,4-dimethoxybenzene with 3-methyl-2-butanol and sulfuric acid what
product was formed...
asked 41 minutes ago -
This programming assignment needs to be written so that it can
do infix expression to postfix...
asked 47 minutes ago -
Below are the reduction half reactions for chemolithoautotrophic
denitrification, where hydrogen is a source of electrons...
asked 47 minutes ago -
On January 2, 2020, the Retail Auto Parts Company received a
notice from its primary supplier...
asked 56 minutes ago