A 2.5 cm diameter PVC water pipe brings city water into a home at a speed...
A 2.5 cm diameter PVC water pipe brings city water into a home at a speed of 0.038 m/s. The city water pipe is 45 cm below ground and the water outlet outside the house is 0.80 meters above ground. The exit velocity from the hose is 0.12 m/s exiting from a 2.5 cm diameter circular nozzle. What is city water pressure?
Homework Answers
Add Answer to:
A 2.5 cm diameter PVC water pipe brings city water into a home
at a speed...
7. Water flows through a pipe of diameter 1.08m at a velocity of 2m/s. If someone...
7. Water flows through a pipe of diameter 1.08m at a velocity of 2m/s. If someone puts a nozzle on the end of the pipe, reducing the diameter to 0.35m, at what speed will the water exit the pipe?. 10. A pipe with a radius of 50 cm has water flowing at 5 m/s. If water goes into a new pipe with radius 33 cm, how much will the pressure decrease? 11. A large dam has a hole that is...
A) Water moves in a pipe that has a diameter of 34 cm at 1 m/s,...
A) Water moves in a pipe that has a diameter of 34 cm at 1 m/s, but then the pipe reduces to a diameter of 16 cm. Find the velocity of the water in the smaller portion of the pipe. B) Water in a hose with an area of 186 mm2 moves at 4 m/s, but then you cover part of the opening of the hose with your finger, and the water shoots out faster at 26 m/s . Find...
Water with pressure of 190 kPa flows down hill through a pipe with a 3.90 cm...
Water with pressure of 190 kPa flows down hill through a pipe with a 3.90 cm diameter hose at a speed of 1.2 m/s. It then exits through a smaller pipe m of diameter 1.50 cm which is 5.00 m below the upper pipe. a. What is the speed of the water exiting at the lower pipe opening? b. What is the water pressure at the exit of the lower pipe. ?
(c) Water flows through a pipe of diameter 0.05 m at a speed of 1.5 m/s....
(c) Water flows through a pipe of diameter 0.05 m at a speed of 1.5 m/s. At the end of the pipe is a nozzle with an outlet diameter of 0.01 m. What is the velocity of the jet of water emerging from the nozzle and the discharge rate? [2 marks]
A garden hose with a diameter of 2.3 cm is used to fill a bucket, which...
A garden hose with a diameter of 2.3 cm is used to fill a bucket, which has a volume of 0.11 cubic meters. It takes 1.8 minutes to fill. An adjustable nozzle is attached to the hose to decrease the diameter of the opening, which increases the speed of the water. The hose is held level to the ground at a height of 1.0 meters, and the diameter of the nozzle is decreased until a flower bed 2.6 meters away...
Question 6 - Minor Losses A tank and piping system is shown. The galvanized pipe diameter is 1.5 cm, and the total length of pipe is 10 m. The two 90° elbows are threaded fittings. The vertical dista...
Question 6 - Minor Losses A tank and piping system is shown. The galvanized pipe diameter is 1.5 cm, and the total length of pipe is 10 m. The two 90° elbows are threaded fittings. The vertical distance from the water surface to the pipe outlet is 5 m. The velocity of the water in the tank is negligible. Find (a) the exit velocity of the water and (b) the height (h) the water jet would rise on exiting the...
Water in a 5 cm diameter pipe is moving at a speed of 50m/s. If the...
Water in a 5 cm diameter pipe is moving at a speed of 50m/s. If the pipe is 1 m off the ground, what size nozzle must be added to fill a bucket 10m away? Propose an alteration to this situation that would allow the bucket to be filled faster and prove your answer.
Water flow in a pipe and then exit through a bended nozzle as shown in Figure...
Water flow in a pipe and then exit through a bended nozzle as shown in Figure 3. The nozzle is connected to the main pipe using a flanged joint at (1). The diameter of the pipe is D1 10 cm and is constant, whilst the diameter at the outlet section of the nozzle (2) is D2 3 em. The flowrate of the water is Q = 15 liter/s and the water pressure at the flange is Pi 230 kPa. By...
QUESTION 6 A pipe with an internal diameter of 2.54 2.67 cm attaches to a hose...
QUESTION 6 A pipe with an internal diameter of 2.54 2.67 cm attaches to a hose with an internal diameter of 1.11 1.017 cm. It is determined that water flows through the pipe with a velocity of 0.755 0.817 m/s. With what velocity does the water flow through the hose?
A flow nozzle equipped with a differential pressure gage is used to measure the flow rate of water at 10°C (p 9997 kg/m3 and p 1.307 x 10-3 kg/m s) through a 3-cm-diameter horizontal pipe. The nozzle...
A flow nozzle equipped with a differential pressure gage is used to measure the flow rate of water at 10°C (p 9997 kg/m3 and p 1.307 x 10-3 kg/m s) through a 3-cm-diameter horizontal pipe. The nozzle exit diameter is 1.5 cm, and the measured pressure drop is 3.3 kPa. Determine the volume flow rate of water, the average velocity through the pipe, and the head loss 1.5 cm Differential pressure gage -3 m3(s m/s The volume flow rate of...
(c) Water flows through a pipe of diameter 0.05 m at a speed of 1.5 m/s. At the end of the pipe is a nozzle with an outlet diameter of 0.01 m. What is the velocity of the jet of water emerging from the nozzle and the discharge rate? [2 marks]
A garden hose with a diameter of 2.3 cm is used to fill a bucket, which has a volume of 0.11 cubic meters. It takes 1.8 minutes to fill. An adjustable nozzle is attached to the hose to decrease the diameter of the opening, which increases the speed of the water. The hose is held level to the ground at a height of 1.0 meters, and the diameter of the nozzle is decreased until a flower bed 2.6 meters away...
Question 6 - Minor Losses A tank and piping system is shown. The galvanized pipe diameter is 1.5 cm, and the total length of pipe is 10 m. The two 90° elbows are threaded fittings. The vertical distance from the water surface to the pipe outlet is 5 m. The velocity of the water in the tank is negligible. Find (a) the exit velocity of the water and (b) the height (h) the water jet would rise on exiting the...
Water in a 5 cm diameter pipe is moving at a speed of 50m/s. If the pipe is 1 m off the ground, what size nozzle must be added to fill a bucket 10m away? Propose an alteration to this situation that would allow the bucket to be filled faster and prove your answer.
Water flow in a pipe and then exit through a bended nozzle as shown in Figure 3. The nozzle is connected to the main pipe using a flanged joint at (1). The diameter of the pipe is D1 10 cm and is constant, whilst the diameter at the outlet section of the nozzle (2) is D2 3 em. The flowrate of the water is Q = 15 liter/s and the water pressure at the flange is Pi 230 kPa. By...
QUESTION 6 A pipe with an internal diameter of 2.54 2.67 cm attaches to a hose with an internal diameter of 1.11 1.017 cm. It is determined that water flows through the pipe with a velocity of 0.755 0.817 m/s. With what velocity does the water flow through the hose?
A flow nozzle equipped with a differential pressure gage is used to measure the flow rate of water at 10°C (p 9997 kg/m3 and p 1.307 x 10-3 kg/m s) through a 3-cm-diameter horizontal pipe. The nozzle exit diameter is 1.5 cm, and the measured pressure drop is 3.3 kPa. Determine the volume flow rate of water, the average velocity through the pipe, and the head loss 1.5 cm Differential pressure gage -3 m3(s m/s The volume flow rate of...
Most questions answered within 3 hours.
-
Task 5.2 Numerical Analysis Using Nested Loops (13 pts)
Consider the following program:
void setup()
{...
asked 8 minutes ago -
If a lossless transformer has 1000 turns for a primary winding
and 100 turns for the...
asked 16 minutes ago -
Write the net ionic equation for the precipitation reaction that
occurs when aqueous solutions of potassium...
asked 25 minutes ago -
it
should be written in c++
Your program should take numbers from the user until the...
asked 31 minutes ago -
Buses are powered by chemical reactions. Define matter and the
four states of matter. What is...
asked 48 minutes ago -
Use conservation of energy to find the velocity of a free point
charge q1 at 22cm...
asked 55 minutes ago -
First, describe policies promoted by governments of the
political right to address economic globalization. Second, describe...
asked 1 hour ago -
M2-9 Completing T-Accounts LO2-4
Following are the transactions of Dennen, Inc., for the month of
January....
asked 1 hour ago -
Write a program using python that reads from values from a text
file and plots them...
asked 1 hour ago -
Look up the density of
the metal of the object used in parts A and B...
asked 1 hour ago -
Discuss strategic considerations that Amazon and NYC politicians
had. Analyze why the deal between Amazon and...
asked 1 hour ago -
A combustion reaction is describes as a carbon source reacting
with oxygen and producing carbon dioxide...
asked 1 hour ago