Please explain the steps properly
P.S: If you are having any doubt, please comment here, I will surely reply you.Please provide your valuable feedback by a thumbsup. Your thumbsup is a result of our efforts. Thanks in advance!
Please explain the steps properly 3. Draw the Isometric projection for the given orthographic 30 angle...
given the front and left side use 45 angle projection and draw the top view. then complete another 3 orthographic views by first drawing the front view revolved clockwise on A as a pivot until milled slot is horizontal for cutting on a milling machine, then project top and left side. dimension all views. Milling Cutter .5 .38 1.5O 1.62 3.25 45 3.50 Milling Cutter .5 .38 1.5O 1.62 3.25 45 3.50
QUESTION 1 Figure 1 shows the components of a swivel and base assembly Draw according to scale 1 1, in first angle orthographic projection, the following views when assembled -A full sectional front view on plane A-A (25 -A left view and (1 - A title block No hidden lines need be shown Insert the item numbers on your drawing The complete parts list is as foliows Item 1 Base (cast iron)- one required- Item 2 Swivel 9cast iron)- one...
Ex 7-4 Draw in Exercise Problems EX7-3 through EX7-6. two orthographic views and an auxiliary view for each o EX7-4 Millimeters 14 50 80 50 10 56.6 30 80 R6 60 40 130 45 EX7-6 Millimeters
MAY/JUNE 2017 QUESTION 1 Figure 1 shows the components of an IDLER PULLEY Draw according to scale 1 1, ın first angle orthographic projection, the following views when assembled - A full sectional front view (According to component 1 section) - A left view (24) (14) - And a title block Insert item numbers in the assembly drawing The complete part list is as follows | DESCRIPTION | MATERIAL QUANTITY BODY PULLEY PIN SHAFT BUSH HEXAGONAL NUT I M S...
with section GIVEN BELOW THE ISOMETRIC DRAWING OF A BRACKET MADE OF STEEL DRAl THE FOLLOWING VIEWS USING 11 SCALE AND THIRD ANGLE PROJECTION 1-SEC FV A-A 2-TV 3-RSV 25 10 15 R20 #20 25 70 30 R5 20 R30 110 AHED ALKHATEEB ID NO. BENCH NO. TITLE MATERIAL GROUP NO. KING SAUD UNIVERSITY DATE CW NO. SCALE OL OL nc
DRAW THE PROJECTION OF THE FOLLOWING LINES 1. A line AB 40 mm long is parallel to VP and inclined at an angle of 30° to HP. The end A is 15 mm above HP and 20 mm in front of VP. Draw the projections of the line. 2. Draw the projections of straight line AB 60 mm long parallel to HP and at an angle of 40° to VP. The end A is 30 mm above HP and 20...
Direction Please read the questions carefully. Please draw the cash flow diagrams and explain the steps that you are going to approach to solve the problems then solve the problem. Show the details in solving the problems. Please write legible hard writing, otherwise there is a deduction from your grade 10 points. Missing Cash Flow Diagram is deductible points equal to 20% of the total points for each question Question (1) An elevator company has redesigned their prod- uct to...
What type of reaction happened if 3-chlorohexane reacted with water to form hexan-3-ol given the following chart and why? Draw the mechanism. Angle of light rotation as reaction proceeds 130 105 80 55 30 5 -20 O . -45 -70 -95 - 120 0 2 4 6 8 10
please show all work in clean and legible handwriting with all labels and steps that is properly explained for PROBLEMS #1, 2, 3, AND 4. Any incorrect answers and not solving all 4 problems will get an immediate thumbs down because they did not follow directions, thank you 1) Express the triple integral Ⅲf (x,y,z) dV as an iterated integral in the two a) E={(x,y,z)Wr2+yszaj orders dzdy dr and dz dr dy where b) Sketch the solid region E c)...
PLEASE EXPLAIN ALL STEPS 4. Suppose the diagram of an electrical system is as given in the figure below. 0.85 0.92 0.95 0.75 (a) What is the probability that the system works? Assume the components fail inde- pendently. Round only your final answer to 3 decimals. (b) Given that the system works, what is the probability that the component C is not working? Round only your final answer to 3 decimals