Reinforced Concrete Design
Design a rectangular beam section for the load given W(dead) =29.40kN/m, W(live) = 43.20kN/m, L1=4.82m, L2= 1.5m, use row(p)=0.18f'c/fy. Beam weight is not included in the loads shown. fy = 414 MPa, f’c = 28 MPa. Live loads are to be placed where they will cause the most severe conditions at the sections being considered. Select the beam size for the largest moment (positive or negative), and then select the steel required for maximum positive and negative moment. Assume concrete weighs 23.5 kN/m3 . Show sketches of cross-section, including bar sizes, arrangement and spacing. Show analysis computation after the design.
Homework Answers
Request Answer!
We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead load moment (MD=500 kN.m) and a service live load moment (ML = 400 kN.m). Design the section as a double reinforced section (the dimensions can't be increased). Place the compression reinforcement at 65 mm from the compression face. Compressive strength of concrete; fe 28 MPa, yielding stress of reinforcement; fy= 420 MPa. Assume 30 mm to be used in the tension (two layers), 26...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead load moment (MD= 500 kN.m) and a service live load moment (ML = 400 kN.m). Design the section as a double reinforced section (the dimensions can't be increased). Place the compression reinforcement at 65 mm from the compression face. Compressive strength of concrete; fc = 28 MPa, yielding stress of reinforcement; fy= 420 MPa. Assume 30 mm to be used in the tension (two...
reinforced concrete design , ACI code Shear Strength of Flexural Members Design for shear forces The...
reinforced concrete design , ACI code
Shear Strength of Flexural Members Design for shear forces The simply supported beam shown is subjected to ultimate (factored) distributed and concentrated loads 1. Determine the shear capacity of concrete at the critical section according to ACI318-14 detailed method in Table 22.5.5.1. Design the shear reinforcement and determine the locations on the beam shear force diagram where this shear reinforcement should be placed. 2. 3. Determine the locations within the beam where minimum shear...
For Problems 1 and 2, design rectangular sections for the beams. Loads and Density values are...
For Problems 1 and 2, design rectangular sections for the beams.
Loads and Density values are shown. Beam weights are not included
in the loads shown. Show sketches of cross sections, including bar
sizes, arrangement, and spacing. Assume concrete weighs 150
lb/ft3, fy = 60,000 psi, and fc′ =4000 psi, unless given
otherwise.
2. Design a cantilever beam. The loading cases are shown in Figure 2: Wp = 3 k/ft, w, = 1 kft MITIMIZ 12f- Use p= 0.1852 Figure...
Name: Date: 2. (+35) Design a typical interior tension-reinforced T-beam to resist positive moment. Beam dimension...
Name: Date: 2. (+35) Design a typical interior tension-reinforced T-beam to resist positive moment. Beam dimension is given. The service loads are 150 psf dead load (doesn't include the beam weight) and 350 psf live load. The beam is on a simple span of 20 ft. Use f:=4000 psi for strength concrete and fy=60000 psi for steel reinforcement. 8-0* (typ.)
Assume normal concrete weight (wc = 143 lb/ft) with specified compressive strength fc = 4,000 psi,...
Assume normal concrete weight (wc = 143 lb/ft) with specified compressive strength fc = 4,000 psi, and steel Grade 60 (fy = 60,000 psi). For design loads assume dead load wd = 30 lb/ft? (excluding self-weight) and live load we = 100 lb/ft. Finally assume that the steel percentage ratio is equal to p= 0.18fc/fy. Design an interior one-way simply supported slab with a 15 ft span using the above assumptions. Show sketches of one-way slab cross section, including reinforcing...
Problem 3 Assume normal concrete weight (wc = 143 lb/ft) with specified compressive strength fc =...
Problem 3 Assume normal concrete weight (wc = 143 lb/ft) with specified compressive strength fc = 4,000 psi, and steel Grade 60 (fy = 60,000 psi). For design loads assume dead load wd = 30 lb/ft? (excluding self-weight) and live load wų = 100 lb/ft. Finally assume that the steel percentage ratio is equal to p= 0.18fc'/fy. Design an interior one-way simply supported slab with a 15 ft span using the above assumptions. Show sketches of one-way slab cross section,...
Problem 1 Reinforced Concrete T-Flanged Sections (50 pts.) You are required to analyze and design...
Problem 1 Reinforced Concrete T-Flanged Sections (50 pts.) You are required to analyze and design the propped cantilever t-section from HM 4 but for shear only. Draw shear V and moment M diagrams for uniformly distributed load throughout the 30ft span and equally concentrated loads at 10ft and 30ft. Recall that the connection at the left joint N1 is fixed. The connection at 20ft N3 is a roller. The right end node N2 is a free end. Use a concrete...
Problem 1 Reinforced Concrete T-Flanged Sections (50 pts.) You are required to analyze and design...
Problem 1 Reinforced Concrete T-Flanged Sections (50 pts.) You are required to analyze and design the propped cantilever t-section from HM 4 but for shear only. Draw shear V and moment M diagrams for uniformly distributed load throughout the 30ft span and equally concentrated loads at 10ft and 30ft. Recall that the connection at the left joint N1 is fixed. The connection at 20ft N3 is a roller. The right end node N2 is a free end. Usea concrete compressive...
Renforcement concrete design (ACI-code 2019) 2- Design the beam for the slab shown below. The beam...
Renforcement concrete design (ACI-code 2019)
2- Design the beam for the slab shown below. The beam is carrying a service moment of 450 kN.m. Take f = 21 MPa and fy = 414 MPa. hf=75mm 1.2m 7.3 m 540 mm 300mm
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead load moment (MD=500 kN.m) and a service live load moment (ML = 400 kN.m). Design the section as a double reinforced section (the dimensions can't be increased). Place the compression reinforcement at 65 mm from the compression face. Compressive strength of concrete; fe 28 MPa, yielding stress of reinforcement; fy= 420 MPa. Assume 30 mm to be used in the tension (two layers), 26...
A reinforced concrete beam with dimensions (300 mm * 800 mm) subjected to a service dead load moment (MD= 500 kN.m) and a service live load moment (ML = 400 kN.m). Design the section as a double reinforced section (the dimensions can't be increased). Place the compression reinforcement at 65 mm from the compression face. Compressive strength of concrete; fc = 28 MPa, yielding stress of reinforcement; fy= 420 MPa. Assume 30 mm to be used in the tension (two...
reinforced concrete design , ACI code
Shear Strength of Flexural Members Design for shear forces The simply supported beam shown is subjected to ultimate (factored) distributed and concentrated loads 1. Determine the shear capacity of concrete at the critical section according to ACI318-14 detailed method in Table 22.5.5.1. Design the shear reinforcement and determine the locations on the beam shear force diagram where this shear reinforcement should be placed. 2. 3. Determine the locations within the beam where minimum shear...
For Problems 1 and 2, design rectangular sections for the beams.
Loads and Density values are shown. Beam weights are not included
in the loads shown. Show sketches of cross sections, including bar
sizes, arrangement, and spacing. Assume concrete weighs 150
lb/ft3, fy = 60,000 psi, and fc′ =4000 psi, unless given
otherwise.
2. Design a cantilever beam. The loading cases are shown in Figure 2: Wp = 3 k/ft, w, = 1 kft MITIMIZ 12f- Use p= 0.1852 Figure...
Name: Date: 2. (+35) Design a typical interior tension-reinforced T-beam to resist positive moment. Beam dimension is given. The service loads are 150 psf dead load (doesn't include the beam weight) and 350 psf live load. The beam is on a simple span of 20 ft. Use f:=4000 psi for strength concrete and fy=60000 psi for steel reinforcement. 8-0* (typ.)
Assume normal concrete weight (wc = 143 lb/ft) with specified compressive strength fc = 4,000 psi, and steel Grade 60 (fy = 60,000 psi). For design loads assume dead load wd = 30 lb/ft? (excluding self-weight) and live load we = 100 lb/ft. Finally assume that the steel percentage ratio is equal to p= 0.18fc/fy. Design an interior one-way simply supported slab with a 15 ft span using the above assumptions. Show sketches of one-way slab cross section, including reinforcing...
Problem 3 Assume normal concrete weight (wc = 143 lb/ft) with specified compressive strength fc = 4,000 psi, and steel Grade 60 (fy = 60,000 psi). For design loads assume dead load wd = 30 lb/ft? (excluding self-weight) and live load wų = 100 lb/ft. Finally assume that the steel percentage ratio is equal to p= 0.18fc'/fy. Design an interior one-way simply supported slab with a 15 ft span using the above assumptions. Show sketches of one-way slab cross section,...
Problem 1 Reinforced Concrete T-Flanged Sections (50 pts.) You are required to analyze and design the propped cantilever t-section from HM 4 but for shear only. Draw shear V and moment M diagrams for uniformly distributed load throughout the 30ft span and equally concentrated loads at 10ft and 30ft. Recall that the connection at the left joint N1 is fixed. The connection at 20ft N3 is a roller. The right end node N2 is a free end. Use a concrete...
Problem 1 Reinforced Concrete T-Flanged Sections (50 pts.) You are required to analyze and design the propped cantilever t-section from HM 4 but for shear only. Draw shear V and moment M diagrams for uniformly distributed load throughout the 30ft span and equally concentrated loads at 10ft and 30ft. Recall that the connection at the left joint N1 is fixed. The connection at 20ft N3 is a roller. The right end node N2 is a free end. Usea concrete compressive...
Renforcement concrete design (ACI-code 2019)
2- Design the beam for the slab shown below. The beam is carrying a service moment of 450 kN.m. Take f = 21 MPa and fy = 414 MPa. hf=75mm 1.2m 7.3 m 540 mm 300mm
Most questions answered within 3 hours.
-
True or False : If we believe that the effect of advertising for
a vacation resort...
asked 18 minutes ago -
Observer A stands at the top of the cliff and throws a ball
straight upwards with...
asked 9 minutes ago -
Witness Manufacturing produces two types of cameras: 35mm and
digital. The cameras are produced using one...
asked 10 minutes ago -
For the net cash flow
series, find the external rate of return (EROR) using the MIRR...
asked 13 minutes ago -
The United States has a population of 327 million and has 206
million people that are...
asked 14 minutes ago -
Calculate the energy E of a sample of 2.10 mol of ideal oxygen
gas ( O...
asked 17 minutes ago -
On January 31, 2018, Allowance for Doubtful Accounts has a
credit balance of 25,000. During 2018,...
asked 18 minutes ago -
FOR INCOME TAX PURPOSES, THE SALE OF AN UNICORPORATED BUSINESS
DOES WHICH OF THE FOLLOWING
GENERALLY...
asked 48 minutes ago -
Eileen and Sarah begin the bean Buzz Coffee Shop in
2016 as equal partners. In 2018,...
asked 48 minutes ago -
draw a schematic model of the molecular architecture
for HDPE, LLDPE and LDPE.
asked 57 minutes ago -
10. A.) Illustrate the impact of a change that occurs in an
economy when the level...
asked 1 hour ago -
Light is gathered from a distant galaxy and one of the spectral
lines of Calcium is...
asked 1 hour ago