Thanks
a=4 b=6 c=1 d=0.8 5.For the position shown, determine the force in hydraulic cylinder EC if...
a=6 b=6 c=2
3. Find a reaction forces at A and B using the free-body diagram of the entire truss (10p). b. determine the force in members BC, BE and EF of the truss. Indicate whether the members are in tension or compression (10p). Take =Last number of your ID b = Second number of your ID (m) P = Eighth number of your ID a (kN) If any term (a, b or P) is zero, take 1. 1 D...
H. HYDRAULIC MOTOR DRIVE A. HYDRAULIC CLAMP CYLINDER B OOOO CLAMP UNIT -INJECTION UNIT Figure 6-1. Plastics Injection Molding Machine Your task is to design a circuit to control the injection molding machine. The control circuit should perform the following functions. • Pressing pushbutton 1PB starts the cycle. • The mold closes (cylinder 2 extends). • When the mold is closed (cylinder 2 extended), a limit switch is actuated. This causes plastic to be injected into the mold ( motor...
4. The hydraulic cylinder D extends with a velocity of vAft/s and an acceleration of -1.5ft/s2. Determine the velocity and the accelerat ap on of C at the instant shown 1 ft 2 ft 8-4 ft/s ав 1.5ft/s
4. The hydraulic cylinder D extends with a velocity of vAft/s and an acceleration of -1.5ft/s2. Determine the velocity and the accelerat ap on of C at the instant shown 1 ft 2 ft 8-4 ft/s ав 1.5ft/s
The frame is used to support the 58-kg cylinder(Figure 1). Determine the force of the pin at C on member ABC. Express your answer with the appropriate units. μΑ ? FABC = Value Units Figure Submit Request Answer < 1 of 1 0.8 m 0.8 m Part B 100 mm Determine the force of the pin at C on member CD. Express your answer with the appropriate units. A B 100 mm 1.2 m μΑ ? FCD = Value Units...
Hydraulic engineering:
The static head or static lift for the system is:
A.4
B.5
C.2
D.1
E.3
--- @CENTRIFUGAL PUMP HEAD CURVE A HEAD CURVE (+) HOLL Q Coprn)
part a, b, c & d are
correct
Week 4, Question 2: Use the force method to determine the force in each member of the truss. Take a = 7 kN, b = 8 kN, c = 11 kN and EA = 20000 kN (for all the members). B) 2 m 3 m— 3 m Please fill in your solutions here: a) FAB = -11 kN Your last answer was interpreted as follows: -11 b) FAC = 0 KN Your...
(1 point) Difficulty (4/5) HOW U EC THEM DOGS? 2013 C@SO Michael Swanbom BY NC SA A truss structure is used to hang signs at an entrance to a stadium. The locations of the centers of gravity of the signs are given by dimensions c and d. Find the forces and stresses carried in the members indicated in the table below, as well as the changes in length of those members. Dimensions, weights, and cross-sectional areas are given below. The...
Member BCD is supported in the position shown using the 1/2 ×
1/4 in2 rod AC and 1/4 in diameter pins at B, C&D. The ultimate
bearing stress for the pin at B is 5ksi, the ultimate shear stress
for the pin at B is 7 ksi and the ultimate normal stress for the
link AC is 12ksi. Assuming that the pins at A and C are strong and
a factor of safety of 3 is desired, determine
(a) The...
5. How many stable structure(s) are shown below? A. 0 B. 1 C. 2 D. 3 E. 4 6. Determine the number of zero-force members for the following truss A. 8 B. 10 C. 12 D. 22 E. None of the above
Explain ur working
4. [6 marks] Using the following graph representation (G(VE,w)): V a, b,c, d,e, fh E -la, b, [a, fl,la,d, (b,ej, [b,d, c,fl,fc,d],Id,el, sd, f) W(a, b) 4, W(a, f)-9, W(a, d)-10 W(b, e) 12, W (b, d)7, W(c,d) 3 a) [3 marks] Draw the graph including weights. b) [2 + 1-3 marks] Given the following algorithm for finding a minimum spanning tree for a graph: Given a graph (G(V,E)) create a new graph (F) vith nodes (V)...