Water is to be withdrawn from a 3-m-high water reservoir by drilling a 1.5-cm- diameter hole...
Water is to be withdrawn from a 3-m-high water reservoir by drilling a 1.5-cm- diameter hole in the center of the bottom surface. Disregarding the effect of the kinetic energy correction factor, determine the flow rate of water through the hole for
a) a sharp edged entrance followed by threaded 90° bend and then a 3.5m length of wrought iron pipe and finally a fully open Globe Valve
b) redo a) for the ideal case with no viscous losses
Homework Answers
Add Answer to:
Water is to be withdrawn from a 3-m-high water reservoir by
drilling a 1.5-cm- diameter hole...
Two water reservoirs A and B are connected to each other through a 35m-long, 2-cm-diameter cast...
Two water reservoirs A and B are connected to each other through a 35m-long, 2-cm-diameter cast iron pipe with a sharp-edged entrance. The pipe also involves a swing check valve and a fully open gate valve. The water level in both reservoirs is the same, but reservoir A is pressurized by compressed air while reservoir B is open to the atmosphere at 94 kPa. If the initial flow rate through the pipe is 1.2 L/s, determine the air pressure (gage)...
2. Water flows at a rate of 60 L/s from a main reservoir to a subsidiary...
2. Water flows at a rate of 60 L/s from a main reservoir to a subsidiary through a 600 m long, 185 mm diameter asphalted cast iron pipe as shown in the figure. The pipeline contains a gate valve, a globe valve and 4 standard 90° elbows. The entrance and exit are square edged, and all fittings are screwed ends, determine, You need Kinematic viscosity of water, 1 x 10-6 m/s2 (a) The friction head loss in the pipe, (b)...
Water, with density of 1000 kg/m3 and kinematic viscosity of 1.0 x 10- m2/s, is pumped through a ...
Water, with density of 1000 kg/m3 and kinematic viscosity of 1.0 x 10- m2/s, is pumped through a total length of 60 m of pipe from a lower reservoir to a higher reservoir. The inner diameter of the pipe is 30 cm. Both reservoirs are open to the atmosphere, and the water surface of the higher reservoir is 10 m above that of the lower reservoir. The entrance from the lower reservoir to the pipe is sharp-edged, and along the...
Two water reservoirs A and B are connected to each other through a 35m-long, 2-cm-diameter cast...
Two water reservoirs A and B are connected to each other through a 35m-long, 2-cm-diameter cast iron pipe with a sharp-edged entrance. The pipe also involves a swing check valve and a fully open gate valve. The water level in both reservoirs is the same, but reservoir A is pressurized by compressed air while reservoir B is open to the atmosphere at 94 kPa. If the initial flow rate through the pipe is 1.2 L/s, determine the air pressure (gage)...
Problem 5: The system in the Figure consists of 1200 m of 5 cm cast-iron pipe, two 45o and four 90 flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If...
Problem 5: The system in the Figure consists of 1200 m of 5 cm cast-iron pipe, two 45o and four 90 flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m3/s of water at 20°C into the reservoir? Elevation 500 m Sharp exit 45° Open globe 45
Problem 5: The system in the...
Water (p=998kg/m^3, u=0.001Pa*s) flows from reservoir A to reservoir B through the piping system shown. Each...
Water (p=998kg/m^3,
u=0.001Pa*s) flows from reservoir A to reservoir B through the
piping system shown. Each elbow has a minor loss coefficient of
1.2. Each valve has a minor loss coefficient of 3.2. The entrance
and exit are both sharp edged. Determine the flow rate L/min. You
now need to modify the piping system to increase the flow rate to
100L/min by reducing the length of the 25mm pipe. What must new
length of the 25mm pipe be?
86. Water...
Problem 4 (50 points) water is discharged from a reservoir at a rate of 18.103 m2/s using two horizontal cast iron pipes nected in series and a pump between them. The first pipe is 20 m long and...
Problem 4 (50 points) water is discharged from a reservoir at a rate of 18.103 m2/s using two horizontal cast iron pipes nected in series and a pump between them. The first pipe is 20 m long and has a 6-cm diameter, while the second pipe is 35 m long and has a 4-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged. Losses associated with the connection...
A water tank filled with solar-heated water at 40°C is to be used for showers in...
A water tank filled with solar-heated water at 40°C is to be used for showers in a field using gravity-driven flow. The system includes 39 m of 1.5-cm-diameter galvanized iron piping with four miter bends (90°) without vanes and a wide-open globe valve. If water is to flow at a rate of 1.2 L/S through the shower head, determine how high the water level in the tank must be from the exit level of the shower. Disregard the losses at...
fluid mechanics ASAP please Problem 4 (50 points) Water is discharged from a reservoir at a rate of 18.103 m3/s using two horizontal cast iron pipes connected in series and a pump between them. T...
fluid mechanics
ASAP please
Problem 4 (50 points) Water is discharged from a reservoir at a rate of 18.103 m3/s using two horizontal cast iron pipes connected in series and a pump between them. The first pipe is 20 m long and has a 6-cm diameter, while the second pipe is 35 m long and has a 4-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged. Losses...
3) The system in Figure below consists of 1200 m of 5 cm cast-iron pipe, two...
3) The system in Figure below consists of 1200 m of 5 cm cast-iron pipe, two 45° and four 90° flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m3/s of water at 20°C into the reservoir? (For water at 20°C, take p-998 kg/m3 and u-0.001 kg/m-s. For cast iron, take ε 0.26...
Two water reservoirs A and B are connected to each other through a 35m-long, 2-cm-diameter cast iron pipe with a sharp-edged entrance. The pipe also involves a swing check valve and a fully open gate valve. The water level in both reservoirs is the same, but reservoir A is pressurized by compressed air while reservoir B is open to the atmosphere at 94 kPa. If the initial flow rate through the pipe is 1.2 L/s, determine the air pressure (gage)...
2. Water flows at a rate of 60 L/s from a main reservoir to a subsidiary through a 600 m long, 185 mm diameter asphalted cast iron pipe as shown in the figure. The pipeline contains a gate valve, a globe valve and 4 standard 90° elbows. The entrance and exit are square edged, and all fittings are screwed ends, determine, You need Kinematic viscosity of water, 1 x 10-6 m/s2 (a) The friction head loss in the pipe, (b)...
Water, with density of 1000 kg/m3 and kinematic viscosity of 1.0 x 10- m2/s, is pumped through a total length of 60 m of pipe from a lower reservoir to a higher reservoir. The inner diameter of the pipe is 30 cm. Both reservoirs are open to the atmosphere, and the water surface of the higher reservoir is 10 m above that of the lower reservoir. The entrance from the lower reservoir to the pipe is sharp-edged, and along the...
Two water reservoirs A and B are connected to each other through a 35m-long, 2-cm-diameter cast iron pipe with a sharp-edged entrance. The pipe also involves a swing check valve and a fully open gate valve. The water level in both reservoirs is the same, but reservoir A is pressurized by compressed air while reservoir B is open to the atmosphere at 94 kPa. If the initial flow rate through the pipe is 1.2 L/s, determine the air pressure (gage)...
Problem 5: The system in the Figure consists of 1200 m of 5 cm cast-iron pipe, two 45o and four 90 flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m3/s of water at 20°C into the reservoir? Elevation 500 m Sharp exit 45° Open globe 45
Problem 5: The system in the...
Water (p=998kg/m^3,
u=0.001Pa*s) flows from reservoir A to reservoir B through the
piping system shown. Each elbow has a minor loss coefficient of
1.2. Each valve has a minor loss coefficient of 3.2. The entrance
and exit are both sharp edged. Determine the flow rate L/min. You
now need to modify the piping system to increase the flow rate to
100L/min by reducing the length of the 25mm pipe. What must new
length of the 25mm pipe be?
86. Water...
Problem 4 (50 points) water is discharged from a reservoir at a rate of 18.103 m2/s using two horizontal cast iron pipes nected in series and a pump between them. The first pipe is 20 m long and has a 6-cm diameter, while the second pipe is 35 m long and has a 4-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged. Losses associated with the connection...
A water tank filled with solar-heated water at 40°C is to be used for showers in a field using gravity-driven flow. The system includes 39 m of 1.5-cm-diameter galvanized iron piping with four miter bends (90°) without vanes and a wide-open globe valve. If water is to flow at a rate of 1.2 L/S through the shower head, determine how high the water level in the tank must be from the exit level of the shower. Disregard the losses at...
fluid mechanics
ASAP please
Problem 4 (50 points) Water is discharged from a reservoir at a rate of 18.103 m3/s using two horizontal cast iron pipes connected in series and a pump between them. The first pipe is 20 m long and has a 6-cm diameter, while the second pipe is 35 m long and has a 4-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged. Losses...
3) The system in Figure below consists of 1200 m of 5 cm cast-iron pipe, two 45° and four 90° flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m3/s of water at 20°C into the reservoir? (For water at 20°C, take p-998 kg/m3 and u-0.001 kg/m-s. For cast iron, take ε 0.26...
Most questions answered within 3 hours.
-
The Maxit Corporation has a standard costing system in which
variable manufacturing overhead is assigned to...
asked 10 minutes ago -
Let M = 8.00kg, m = 6.00kg, θ = 40.00, and the coefficient of
kinetic friction...
asked 26 minutes ago -
Java. For C through H True or false?
c. Primitive variables must be objects.
d. Integer...
asked 31 minutes ago -
Write a program that turns a 32-bit numeric value (e.g.,
0xFFFFh) and converts it to a...
asked 33 minutes ago -
A motor produces a torque of 0.25 N m at an angular velocity of
7200 revolutions...
asked 47 minutes ago -
***Please answer the below java question***
Are static methods inheritable? Can they be overridden?
asked 49 minutes ago -
In reaching her destination, a backpacker walks with an average
velocity of 1.13 m/s, due west....
asked 49 minutes ago -
Write two C programs that run a
server program and a client program concurrently.
Server program:...
asked 48 minutes ago -
Executive Program Practical Connection Assignment
Subject : Operations Security.
Assignment:
Provide a reflection of at least...
asked 58 minutes ago -
Every time Casey is at bat he has a 0.4 probability of
getting on base (assume...
asked 1 hour ago -
The Walston Company is to be liquidated and has the following
liabilities:
Income taxes
$
9,400...
asked 1 hour ago -
If
the more comprehensive data is available in MEPS, why does the NHIS
still exist? How...
asked 1 hour ago