For the Unknown Liquid, suppose the first three measurements (empty, w/ 5mL, and w/ had no...
4. Suppose that a student performed the experiment and calculations perfectly as directed except that, unknown to the student, the balance was not zeroed but weighed 0.100 g too high throughout the experiment. Would the calculated val- ue for the density of the unknown liquid be correct? That is, would it be equal to, higher than, or lower than the true value. Explain your answer in clear and correct English. 16 LABORATORY EXPERIMENTS IN GENERAL CHEMISTRY ed in question 4...
i dont understand why the molecular weight i calculated
(42.012 g/mol) for my unknown liquid (acetone) is less than the
actual molecular weight (58.08 g/mol). what errors could i have
made in my lab that would account for the difference.
Molecular Weight of a Volatile Liquid In this experiment, an amount of liquid more than sufficient to fill the flask when vaporized is placed in a flask of measured volume and mass. The flask is then heated in a boiling...
Freezing Point Depression: Determination of the Molar Mass of an Unknown Substance Laboratory Record Unknown Identifier #4 (All unknowns are nonelectrolytes, soi-1) Determination of the freezing point of pure l-butyl alcohol: (Record time-temperature data on the next page) 29.62 1. Mass of empty test tube 2. Mass of test tube and t-butyl alcohol after determination of freezing point of pure t-butyl alcohol 50.25 20.71 3. Mass of t-butyl alcohol Determination of the molar mass of an unknown: (Record time-temperature data...
Separating a Mixture, Recrystallization, pre-lab
assignment
could you also explain why you chose that substance for the empty
spaces and question marks
EXPERIMENT 4 Pre-Lab Assignment Separating a Mixture, Recrystalliration Name Date 1. Complete the following flowchart which shows how to separate a mixture of sand, sodium chloride and acetanilide. Notice that after a separation process (a down arrow) the filtered solids are shown on the left and the filtrate (the liquid) is shown on the right. The terminal step...
For the preparation and standardization of NaOH with KHP im supposed to boil water for 1hr and 30 min to remove CO2....the problem is that if I don't boil it for that long and (30 min) b/c of not enough time but I put the water I boiled for 1/2 hr aproximately into a NaOH bottle with a CO2 absorber and stored it there for a few days. I would assume that I would have to boil the water again...but...
10. Write a one-page summary of the attached paper? INTRODUCTION Many problems can develop in activated sludge operation that adversely affect effluent quality with origins in the engineering, hydraulic and microbiological components of the process. The real "heart" of the activated sludge system is the development and maintenance of a mixed microbial culture (activated sludge) that treats wastewater and which can be managed. One definition of a wastewater treatment plant operator is a "bug farmer", one who controls the aeration...
Can someone please help me with this? Thanks a lot!!!
Five Years In, Gauging Imp Mr. Gates comes from the software in- stantly doubles. Biology, by compari- Biology also has a greater tendency versy. For example, doing clinical trials which was once cheap and fast but eth- While Dr. Sievers's Gates grant is not the Serum Institute of India -the world's biggest vaccine maker-to test The foundation is still supporting two The first attaches vaccines to nano- rants skin inside...
summarizr the followung info and write them in your own words and break them into different key points. 6.5 Metering Chamber: 6.5.1 The minimum size of the metering box is governed by the metering area required to obtain a representative test area for the specimen (see 7.2) and for maintenance of reasonable test accuracy. For example, for specimens incorporating air spaces or stud spaces, the metering area shall span an integral number of spaces (see 5.5). The depth of...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...
In your judgement, and given only the facts described in this
case, should the management of Massey energy Company be held
morally responsible for the deaths of the 29 miners? Explain in
detail.
Suppose that nothing more is learned about the explosion other
than what is described in this case. Do you think Don Blankership
should be held morally responsible for the deaths of the 29 miners?
Explain in detail.
Given only the facts described in this case, should the...