Homework Answers
Add Answer to:
A vortex shedding flow meter is used to measure volume flowrate through a 100 mm diameter...
An orifice meter with a 2 inch diameter opening is used to measure the flow rate...
An orifice meter with a 2 inch diameter opening is used to measure the flow rate of water through a horizontal 3 inch diameter pipe. A mercury manometer is used to measure the pressure difference across the orifice. If the differential height of the manometer is 7 inches, determine the volumetric flowrate (gal/min) of water through the pipe. You may assume the discharge coefficient is 0.6.
A venturi meter was installed in a pipe to measure the flow of the water inside....
A venturi meter was installed in a pipe to measure the flow of the water inside. The inlet diameter of the venturi is 25.4mm and the throat diameter is 12.7mm. Determine the actual flow rate in gpm if the throat Reynolds number is 10^5. The density and viscosity of the fluid is 62.4 Ibm/ft^3 and 3.511kg/m-hr, respectively. The venturi coefficient of discharge is 0.95.( do include unit/s in your answer and use two decimal places)
9. (10 points) An orifice meter with a 1.0 inch diameter opening is used to measure...
9. (10 points) An orifice meter with a 1.0 inch diameter opening is used to measure the flow rate of water through a horizontal 3 inch diameter pipe. A mercury manometer is used to measure the pressure difference across the orifice. If the differential height of the manometer is 30 inches, determine the volumetric flowrate (gal/min) of water through the pipe. You may assume the discharge coefficient is 0.6.
9. (10 points) An orifice meter with a 1.5 inch diameter opening is used to measure...
9. (10 points) An orifice meter with a 1.5 inch diameter opening is used to measure the flow rate of water through a horizontal 3 inch diameter pipe. A mercury manometer is used to measure the pressure difference across the orifice. If the differential height of the manometer is 15 inches, determine the volumetric flowrate (gal/min) of water through the pipe. You may assume the discharge coefficient is 0.6.
A venturi meter is used to measure the flow speed of a fluid in a pipe....
A venturi meter is used to measure the flow speed of a fluid in a pipe. The meter is connected between two sections of the pipe (the figure); the cross-sectional area A of the entrance and exit of the meter matches the pipe's cross-sectional area. Between the entrance and exit, the fluid flows from the pipe with speed V and then through a narrow ''throat'' of cross-sectional area a with speed v. A manometer connects the wider portion of the...
A venturi meter is used to measure the flow speed of a fluid in a pipe. The meter is connected...
A venturi meter is used to measure the flow speed of a fluid in a pipe. The meter is connected between two sections of the pipe (Fig. 14-55); the cross-sectional area A of the entrance and exit of the meter matches the pipe's cross-sectional area. Between the entrance and exit, the fluid flows from the pipe with speed V and then through a narrow ''throat'' of cross-sectional area a with speed v. A manometer connects the wider portion of the...
A Venturi meter equipped with a differential pressure gage is used to measure the flow rate...
A Venturi meter equipped with a differential pressure gage is used to measure the flow rate of water at 15°C (p = 999.1 kg/m”) through a 5-cm- diameter horizontal pipe. The diameter of the Venturi neck is 3 cm, and the measured pressure drop is 5.1 kPa. Taking the discharge coefficient to be 0.98, determine the volume flow rate of water and the average velocity through the pipe. 5 cm 3 cm Differential pressure gage Is The volume flow rate...
A flow rate meter is used to measure the flow rate of a water flow from...
A flow rate meter is used to measure the flow rate of a water flow from left to right) in an inclined position. Due to spatial confinement, the two pressure taps-manometer tubes were inclined as well as shown. The meter is similar to a Venturi meter except at the small pipe the pressure tap is a stagnation pressure tap at 2. For the given geometries, calculate: 1) (4 pts)The velocity at the large pipe, in m/s 2) (3 pts)The velocity...
The measured flow rate of water through a 20 mm diameter pipe is 75 L/min. What...
The measured flow rate of water through a 20 mm diameter pipe is 75 L/min. What is the Reynolds (Re) number?
3. (10 points) A laminar flow meter, as shown in Figure, is used to measure the...
3. (10 points) A laminar flow meter, as shown in Figure, is used to measure the steady flow rate of 15.6 °C water through an 0.824-inch pipe. One hundred and twenty (120) tubes with an inner diameter of 0.013" and a length of 2.756" are used as the laminar tubes. The measured pressure drop, Pi-P2, is equal to 4800 pa. Determine the water flow rate. Number of holes n = 120 IOI 그다 i 11 11 1111 Single hole diameter...
A venturi meter was installed in a pipe to measure the flow of the water inside. The inlet diameter of the venturi is 25.4mm and the throat diameter is 12.7mm. Determine the actual flow rate in gpm if the throat Reynolds number is 10^5. The density and viscosity of the fluid is 62.4 Ibm/ft^3 and 3.511kg/m-hr, respectively. The venturi coefficient of discharge is 0.95.( do include unit/s in your answer and use two decimal places)
9. (10 points) An orifice meter with a 1.5 inch diameter opening is used to measure the flow rate of water through a horizontal 3 inch diameter pipe. A mercury manometer is used to measure the pressure difference across the orifice. If the differential height of the manometer is 15 inches, determine the volumetric flowrate (gal/min) of water through the pipe. You may assume the discharge coefficient is 0.6.
A Venturi meter equipped with a differential pressure gage is used to measure the flow rate of water at 15°C (p = 999.1 kg/m”) through a 5-cm- diameter horizontal pipe. The diameter of the Venturi neck is 3 cm, and the measured pressure drop is 5.1 kPa. Taking the discharge coefficient to be 0.98, determine the volume flow rate of water and the average velocity through the pipe. 5 cm 3 cm Differential pressure gage Is The volume flow rate...
A flow rate meter is used to measure the flow rate of a water flow from left to right) in an inclined position. Due to spatial confinement, the two pressure taps-manometer tubes were inclined as well as shown. The meter is similar to a Venturi meter except at the small pipe the pressure tap is a stagnation pressure tap at 2. For the given geometries, calculate: 1) (4 pts)The velocity at the large pipe, in m/s 2) (3 pts)The velocity...
The measured flow rate of water through a 20 mm diameter pipe is 75 L/min. What is the Reynolds (Re) number?
3. (10 points) A laminar flow meter, as shown in Figure, is used to measure the steady flow rate of 15.6 °C water through an 0.824-inch pipe. One hundred and twenty (120) tubes with an inner diameter of 0.013" and a length of 2.756" are used as the laminar tubes. The measured pressure drop, Pi-P2, is equal to 4800 pa. Determine the water flow rate. Number of holes n = 120 IOI 그다 i 11 11 1111 Single hole diameter...
Most questions answered within 3 hours.
-
plz explain: A sound that changes pressure from 100 mPa to 10
mPa has a change...
asked 3 seconds from now -
how to select perpendicular gd&t tolerance value
using IT tolerance. and gave example
asked 9 seconds ago -
What is the measured air concentration from a sample that has 38
μg of contaminant when...
asked 19 minutes ago -
In support of the argument that we have free will, what are the
implications of seemingly...
asked 20 minutes ago -
Share your thoughts concerning the pros and cons of using
natural products as anticancer agents. (please...
asked 29 minutes ago -
Describe in detail how your own actions reflect the
ideas shared in the discussion, and relate...
asked 34 minutes ago -
Name and clearly describe one technique for determining the age
of fossils in geological context. Are...
asked 47 minutes ago -
A ball is thrown with an initial velocity of 20.0 m/s at an
angle of 35.00...
asked 41 minutes ago -
When assessing pension risk, analysts compute ratios for both
long- and short-term risk. Which statement below...
asked 40 minutes ago -
What is the relativistic momentum of a proton traveling at
0.990c?
A. 3.55E–18 kg·m/s
B. 3.52E–18...
asked 49 minutes ago -
Question 1: B cells secrete these types of immunoglobulin
antibodies. Choose all correct.
1. IgD
2....
asked 56 minutes ago -
Please show calculations for this question:
The average income of university graduates is $68,500 with a...
asked 1 hour ago