5. A Load is drawing 800W from a 240v, 50 Hz supply source at o.84 PF....
Q3. from a 240 V, 50 Hz supply as shown in the Figure 3. 24020 Vrms Inductive load with 0.6 lagging Load current 50 A Ohle Capacitor to be connected for power factor improvement Figure 3: a) Assuming that the capacitor shown in the figure is disconnected, calculate the load real (PL), reactive(Q1), and apparent power(SL) (5 marks) b) Draw the load power triangle and indicate real (P.) reactive (Q.), apparent (SL) power, and power factor angle (@.) (5 marks)...
Q1)A half-wave rectifier has a 120 Vrms 60 HZ ac source. The load IS 50 W. Determine the value of a filter capacitor to keep the peak-to-peak nipple across the load to less than 1.5V. Seled the one best answer from the choices given below(a) 410 UF (d) 3270 uF (b) 820 UF (e) 6540 UFQ2)A diode whose internal resistance is 200 is to supply power to a 1000 load from 110V (rms) source pf supply. Calculate(a) peak load current...
Example 9 Three loads are connected in parallel across 1400 V, 60 Hz supply: Load 1: 125 KVA, 0.28 PF lag Load 2: 10 kW, 40 kVAR capacitive load Load 3: 15 kW Find the total kW, kVAR, KVA, and the supply power factor . The KVAR and the capacitance in mF of the capacitor needed to improve the PF to 0.8 lagging
Q-1 A 60Hz, 480V/240V,960V A transformer is supplying a 960W passive load at 240V. The resistances of the primary side and secondary side of the transformer are 1.092 and 0.252 respectively. If the no load losses of the transfomer is given by P-Vã 4800 W where Vn is the input voltage of the transformer in Volt. Answer the following: a) Calculate transformer efficiency b) Do you allow this transformer to be connected to 240V 50Hz distribution system? Explain. c What...
A 60-Hz single-phase AC power network is shown in the figure below with four different loads. The source voltage ES-320 0. Prior to adding the capacitor load for power factor correction, the source current IS-135 30 . Determine the capacitance (in μF) of the capacitive load that will make the power factor unity (pf 1.0) of the system. Enter the one best answer (as a number without the units) from the following choices: Sync 74 % 6 15 kVA 10...
1. A six pole, 240V, 50 Hz three phase squirrel-cage induction motor has a no-load speed of 103 rad/s and a speed regulation of 5% at rated load. Find the amount of slip (in rpm) at full load for this motor. 2.. A 2 HP, 240 VAC, 60 Hz, capacitor-start motor is 75% efficient and draws 10 A at full load. What is this motor's power factor at rated load? 3. A wound rotor, 3 phase induction motor in Mr....
Q5: The circuit show below has two loads connected to 120 V (rms), 60Hz, house-hold supply. The load-1 is a resistive load (lamp) with a total power of 5 kW. The load-2 is a motor drawing 10 kVA at 0.6 power factor, lagging. The capacitor is initially not connected a) Calculate the load currents (phasor) I and 12 14] b) Calculate the supply current I c) What is the power factor of the source when it supplies to both loads?...
A 1500 kW, unity pf, 3-phase, Y-connected, 2300 V-(line), 30 pole, 60 Hz synchronous motor has a synchronous reactance of 1.95 22/phase. For this problem all losses may be neglected. a. Compute the max. torque in Nm which this motor can deliver if it is supplied with power from an infinite bus, and if its field excitation is constant at the value which would result in unity (1.0) pf at rated load. b. Now, suppose that the motor is supplied...
I just need answers to f,g,and h
connected motor is connected to Vi-L 120 3T/6 V-rms, 50 Hz three e resistance and inductance of each phase is 8-Ω and 0.04 H, respectively. The PS. A three-phase phase source. The wire between a source and the motor has 0.1-Ω of resistance and 1 mH inductance. nd the phase voltage. (2 pts.) a single-phase diagram of the system with its values. (5 pts.) c) Find the line current (magnitude and phase) for...
Problem 3 A 50-Hz transformer is operated from a 60 Hz supply. Assume that the load does not change. Discuss the corresponding effects on its flux, reactive power requirements, losses, and efficiency. а- [5 Points] A 50-kVA, 2400/240 V, 60-Hz, single-phase distribution transformer has the following equivalent circuit parameters referred to the high-voltage side Xea 3.0 Req= 0.5 Xm 4,500 S2 Use the equivalent Cantilever model circuit shown in Figure (1). Assume that the load on the secondary of the...