heat capacity of hexane is 2.26 Kj/kg
mass of 25 mol of hexane = (25*86) =2150 g = 2.15kg where 86 is the molar mass of hexane
heat required = m*Cp*(1293.14 - 412)
= 2.15*2.26*881.14
= 4281.5 KJ
Question 2 How much heat is required when 25 mols of 1-Hexene is heated at atmospheric...
(25 pts). For steady flow in a heat exchanger at approximately atmospheric pressure, 50 mol of N2 is heated from 80 to 1050 °C. How much heat is transferred? 4. cid = A + BT + CT2 + D fi" CHEMICAL ENGINEERING SERIE Introduction to Thermodynamics Mc McGraw-Hill's Chemical Engineering SEVENTH EDITION J. M. Sm H.C. Van N (25 pts). For steady flow in a heat exchanger at approximately atmospheric pressure, 50 mol of N2 is heated from 80 to...
How much heat is required at constant pressure to melt 1 mole of ice at -25 celsius to steam at 125 celsius?
For the air-conditioning system shown below in which atmospheric air is first heated and then humidified with a steam spray, determine the required heat transfer rate in the heating section and the required steam temperature in the humidification section when the steam pressure is 1 MPa. Heating fluid Steam. P-1 MPa Out In Throttle Atmospheric hir W Ti - SC P-100 kPa T3 -25°C 1 - 90% T: - 24°C P) - 100 kPa V.- 60 /min
the heat of vaporization of water is 40.66 kJ/mol. How much heat is absorbed when 2.88 g of water boils at atmospheric pressure? ____kJ (show wrk)
Question 18 1/1 pts A can filled with air at atmospheric pressure is heated in boiling water until it reaches 100 degrees Celsius. The can is sealed and then cooled such that the pressure inside the can is measured to be 90 kPa. What is the final temperature of the can? 310 K 59 degrees C 290 K 41 degrees C
-/25 !!! Current Attempt in Progress Air at atmospheric pressure and a temperature of 25°C is in parallel flow at a velocity of 5 m/s over a 1-m-long flat plate that is heated from below with a uniform heat flux of 1250 W/m². Assume the flow is fully turbulent over the length of the plate. Evaluate properties at 325 K. (a) Calculate the plate surface temperature, Ts(x). in °C, and the local convection coefficient, hx(x), in W/m².K. at x =...
Suppose 18.7 g of oxygen (O2) is heated at constant atmospheric pressure from 38.5°C to 123°C. (a) How many moles of oxygen are present? (Take the molar mass of oxygen to be 32.0 g/mol) (b) How much energy is transferred to the oxygen as heat? (The molecules rotate but do not oscillate.) (c) What fraction of the heat is used to raise the internal energy of the oxygen?
Convert: 150°C to °F; 25°F to °C, -50°F to °K, 100°C to K, 400K to 'c etc. How much heat is required to increase the temperature of 40g water from 25°C to 100°C? Specific heat of water is 1 cal/g°C. How much heat is required to convert 50g ice at 0°C to water at O'C? Latent heat of fusion for ice LF80 cal/g. How much heat is required to increase the temperature of 20g iron from 25°C to 300°C? Specific...
Question 15 2 Points How much energy is required to heat 44.72 g of H2O from 10.00 oC to 37.50 oC? (Heat capacity of liquid H2O = 75.37 J mol-1 K-1) (type in the numeric value in Joules - give your answer to 4 significant figures, do not include the units in your answer only the number, do not use scientific notation, do not include comma's) BLANK-1 BLANK-1
APPLIED THERMODYNAMICS For the air-conditioning system shown below in which atmospheric air is first heated and then humidified with a steam spray, determine the required heat transfer rate in the heating section and the required steam temperature in the humidification section when the steam pressure is 1 MPa. Heating fluid Steam. P-1 MPa Throttle Atmospheric W Out In air Ti - SC P. 100 kPa T3 -25C $. - 90% T: 24'c P) - 100 kPa V-60 m/min