Glycerin at 20°C flows upward in a vertical 75-mm-diameter round pipe with a centerline velocity of 1.0 m s-1 . Determine the pressure drop and head change (hL = ?P / ?g) in a 10 m length of pipe.
Glycerin at 20°C flows upward in a vertical 75-mm-diameter round pipe with a centerline velocity of...
Glycerin at 20 °C flows upward in a vertical 75-mm-diameter pipe with a centerline velocity of 3.8 m/s. Determine the (a) head loss and (b) pressure drop in a 10-m length of the pipe. (a) h kPa (b) Др —
Answer: 133KPa Show working A 75-mm-diameter galvanized iron pipe, having a roughness of e = 0.2 mm, is to be used to carry water at a temperature of 60°C and with a velocity of 3 m/s. Determine the pressure drop over its 12-m length if the pipe is vertical and the flow is upward. A 75-mm-diameter galvanized iron pipe, having a roughness of e = 0.2 mm, is to be used to carry water at a temperature of 60°C and...
LECTURE Sp 1. Oil (relative density 0.85, dynamic viscosity-4.5x10-2kg/m-s) flows through a 75 mm diameter pipe with a mean velocity of 0.65 m/s. Determine i. the pressure drop in a 500 m length, ii- the friction factor, ii the head loss due to friction, iv. the maximunn velocity, and v. the velocity at 30 mm from the pipe wall. (10 marks) 46 2 9 3 8 4 5 6
Solve the question below Glycerin (specific gravity 1.26) in a processing plant flows in a pipe at a rate of R L/s. At a point where the pipe diameter is 832mm, the pressure is 300 kPa. Find the pressure at a second point where the pipe diameter is 300 mm if the second point is 1.0 m lower than the first point, neglect the head loss.
Question - 6 y 1.26 Glycerin (specific gravity 1.26) in a 300 kPa 600 mm dia processing plant flows in a pipe at a rate of (1) 700 L/s. At a point where the pipe diameter is 600 mm, the pressure is 300 kPa. Find the 700 L/S pressure at a second point where the pipe diameter is 300 mm if the second point is 1.0 m lower than the first point, neglect the head loss. 1 m P.? 300...
Water at 20 C is steadily flowing through a diverging pipe section that is inclined by an angle of 30° with respect to the horizontal (See the figure) The total testing section length is 20 m long with an initial pipe diameter of 10 mm (Section 1) and final diameter of 20 mm (Section 2). The small diameter section shows a gage pressure of 100 kPa and average flow velocity 10 m/s. Other values will be obtained by reaching complete...
Fluid dynamics: please help!! A standard oriice with diameter 25 mm is installed in a horizontal pipe having an inside diameter of 50 mm The pipe is to handle the steady flow of water at 20 °C. The average velocity of months of operation. It is desired to measure the pressure drop across the orifice taps by means of a simple vertical manometer. It is anticipated that the reading on the manometer scale can be obtained with a precision of...
A 150-mm-diameter galvanized iron pipe is used to transport water at T = 30∘C with a velocity of 1.5 m/s. Determine the pressure drop over the 15-m length of the pipe. Problem 10.28 A 150-mm-diameter galvanized iron pipe is used to transport water at T 30° C with a velocity of 1.5 m/s. Use the equation-=-1.8 log Figure 1) Determine the pressure drop over the 15-m length of the pipe. Express your answer to three significant figures and Use the...
Problem 2: Oil at 20 °C (SG 0.88) flows in the 3-cm P= 180 kPa diameter pipe shown in the figure. For the pressure measurements in the figure, determine: a) Whether the flow is up or down b) The head loss between points A and B P 500 kPa 15 m c) The flow rate if losses are about 16% of the 370 velocity head 20 m Problem 2: Oil at 20 °C (SG 0.88) flows in the 3-cm P=...
• Determine the energy loss if glycerin at 25°C flows 30 m through a standard 146.3 mm diameter pipe with an average velocity of 4.0 m/s. (Density = 1258 kg/m3 and dynamic viscosity = 9.6 x 10-1 Pa.s)