F=1800N mm DIMENSIONS AB= 200 BC= 150 BD = 200 F = 1800N 3) CALCULATE THE...
150 150+150+150 200 Dimensions in mm 200 The cross BHDF is supported by two links AB and DE. At the instant shown link AB rotates with a constant angular velocity of 4 rad/s counter-clockwise
400 1000 mm 2) Bar AB in the figure is supported by cables BC and BD and a ball socket support at A. Cable BC is parallel to the Z axis, while cable BD is parallel to the X axis. The 200-N weight of the bar acts at its midpoint. What are the tensions in the cables and the reactions at A 600 mm 600 A Check Answer: Tension in Cable BD equals 166.7 N -200j (N) 2
Question 3 Not yet answered A rectangular plate of dimensions X = 275 mm and Y = 150 mm is formed by welding two triangular plates (see figure). The plate is subjected to a compressive stress ox of 4 MPa in the long direction and a tensile stress oy of 12 MPa in the short direction. Marked out of 5.00 V Flag question Using Mohr's Circle (2 points for the correct drawing): determine the normal stress ow acting perpendicular to...
Q2 (12): Th and parallel pipes BC and BD. The head loss between the lower reservoir and the pump can be ignored. The Darcy friction factor of each pipe is f 0.022. If the flow in pipe AB is 0.20 m'/s and AZ is 10.4 m, determine the total head of pump. What is daily power input (in the unit of Kw-hr) if the pump is running at 80% efficiency? e system shown in the following figure consists of two...
The shown frame ABC has beam AB with a rectangular cross section of 150 mm by 200 mm. Attached rod CB has a cross sectional area of 1250 mm2 and is pin-connected to beam AB at B. Use the Stiffness Method to Find the force in BC and the reactions at A a) Use the Stiffness Method to find the force in BC and the reactions at A If the horizontal displacement at B0.01688 mm, the vertical displacement at B...
Handle structure comprised of 3 round bar elements (AB, BC, CD) as shown in the figure below. The handle is fixed to the wall at A. A 150 lbf force is applied to the free end at D. The dimensions and cross sections are given in the figure. The handle structure is made from AISI 1020 cold drawn (CD) low carbon steel. a) draw the free body diagrams of rods AB, BC, and CD. b) Find the forces, moments and...
roblem 1: The built-up shaft consists of a pipe AB and solid rod BC. Pipe AB has an inner diameter of 20 mm and outer diameter of 28 mm. The length of AB is 200 mm. Rod BC has a diameter of 12 mm and a length of 180 mm. (a) Determine the average normal stress at points D and E (b) If the modulus of elasticity of pipe AB is EAB-200 GPa, Poisson's ratio of rod BC is VBc...
Question 1 A rod AB hinged at A and attached at B to cable BD supports the load shown. Knowing that d 200 mm. determine: a) the tension in cable BD b) the reactions at A Copyright © Th.ko raw-H. Companies Inc. Permission requred for reprodepan or disse, 100 mm 90 N 90 N -100 mm100 mm100 mm Question 1 A rod AB hinged at A and attached at B to cable BD supports the load shown. Knowing that d...
A four bar link mechanism with the following dimensions is acted upon by a force \(80 \mathrm{~N} 150^{\circ}\) on the link DC [as shown in the Figure below]: \(\mathrm{AD}=500 \mathrm{~mm}, \mathrm{AB}=400 \mathrm{~mm}, \mathrm{BC}=1000 \mathrm{~mm}, \mathrm{DC}\)\(=750 \mathrm{~mm}, \mathrm{DE}=350 \mathrm{~mm}\) Determine the input torque \(\mathrm{T}\) on the link \(\mathrm{AB}\) for the static equilibrium of the mechanism for the given configuration.Show all your calculations, drawing and septs to solve this problem
200 mm Problem (7) In the position shown, bar AB has an angular velocity of 4 rad/s CW. Determine the angular velocity of bars BD and DE QA 250 mm 150 mm B.............................