Two wooden planks, each 22 mm thick and 160 mm wide, are joined by the glued...

Question

Question

Two wooden planks, each 22 mm thick and 160 mm wid

Answer 1

Answer #1

allowable length d = [(7)/(820 * 0.160 * 0.022)] * 0.020

= 0.0485 m

= 48.5 mm

Answer 2

Similar Homework Help Questions

are f wooden members are joined by plywood splice plates th y glued on the contact...

are f wooden members are joined by plywood splice plates th y glued on the contact surfaces. Knowing that the cle rmi at ear. t the ne 6 mm and tha the length aring stress in the glued joint is 2.5 MPa, dete shown. atnce between the ends of the members is ultimate sh L for which the factor of safety is 2.75 for the loading 16 kN 6 mm -125 mm 6 kN Fig. P1.43
3.28 is not the right answer please units in kips Do not round intermediate calculations. Give...

3.28 is not the right answer please units in kips Do not round intermediate calculations. Give your final answer(s) to three significant figures. 7/8 in. 2 in. 2 in. 1 in. Two wooden planks, eachin. thick and 9 in. wide, are joined by the dry mortise joint shown. Knowing that the wood used shears off along its grain when the average shearing stress reaches 1.25 ksi, determine the magnitude P of the axial load that will cause the joint to...
2. Two wooden members of uniform cross section are joined by a scarf splice joint and...

2. Two wooden members of uniform cross section are joined by a scarf splice joint and subject to a load P. Assuming a maximum allowable shear stress in the glued spice of 60 psi, determine the maximum load P that can be applied. What is the corresponding normal stress in the splice?

Q4. Three steel plates, each 16 mm thick, are joined by two 20-mm diameter rivets as...

Q4. Three steel plates, each 16 mm thick, are joined by two 20-mm diameter rivets as shown in the figure. Determine the following: a. If the load P = 50 kN, what is the largest bearing stress acting on the rivets? b. If the ultimate shear stress for the rivets is 180 MPa, what force Pult is required to cause the rivets to fail in shear? (Disregard friction between the plates.) P/2 P/2 OO
Two steel plates, each ¼ inch thick, are to be joined by two fillet welds. If...

Two steel plates, each ¼ inch thick, are to be joined by two fillet welds. If the joint is to withstand a load of 50,000 lb and an E7014 electrode (allowable tensile strength – 21,000 psi) is used, determine the length of weld at each edge. If the plate width is 10 inches, how would you distribute the weld? Draw a sketch.
Problem 4 (10 pts) A cold-rolled yellow-brass plate, 250 mm long, 150 mm wide and 6...

Problem 4 (10 pts) A cold-rolled yellow-brass plate, 250 mm long, 150 mm wide and 6 mm thick is subjected to a 100 kN centric axial load along its length, as shown. If E-1 1 1 GPa and v 0.3, determine the new dimensions of the plate I5o l ic cuhiected i to an axial tensile force of 5kN. If the maximum allowable normal

A steel tube of 25 mm OD is to be adhesively joined to another steel tube...

A steel tube of 25 mm OD is to be adhesively joined to another steel tube of 25 mm ID, using an adhesive. The assembly will operate at room temperature and an axial load of 12 kN will have to be supported. Using a safety factor of two: a) calculate the minimum length of the lap joint (i.e. depth of overlap of the tubes) to achieve this strength requirement if epoxy is used. Question 2 A steel tube of 25...
A plate 95 mm wide, 190 mm long, and 11.4 mm thick is loaded in tension...

A plate 95 mm wide, 190 mm long, and 11.4 mm thick is loaded in tension in the direction of the length. The plate contains a crack as shown in the figure below with the crack length of 15.2 mm. The material is steel with KIC= 80 MPa (m)(1/2) and Sy= 950 MPa. 6.0 5.0 4.0 3.0 h/b=0.5 1.0 2.0 1.0 0.2 0.4 a/b ratio Ignoring stress concentration, determine the maximum possible load that can be applied to the plate...
A plate 92 mm wide, 184 mm long, and 11.04 mm thick is loaded in tension...

A plate 92 mm wide, 184 mm long, and 11.04 mm thick is loaded in tension in the direction of the length. The plate contains a crack as shown in the figure below with the crack length of 147 mm. The material is steel with KC = 80 MPa (my(12) and Sy=950 MPa. 7.0 6.0 3.0 40 10 /b=05 1.0 2.0 10 02 0.6 0.8 w/braio Ignoring stress concentration, determine the maximum possible load that can be applied to the...